Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
why the hell is my front end shake'n like f#*k????????
why the hell is my front end shake'n like f#*k????????
the front end of my gq is shaking like fuck it has good radius arm bushes and every thing looks good. tyres are balenced. shakes very very bad so bad that i poo myself at about 45Kph. NEED HELP
Re: why the hell is my front end shake'n like f#*k????????
What have you changed lately?
panhard bushes?
BTW, theres 123908 other threads on it, its very common with patrols.
panhard bushes?
BTW, theres 123908 other threads on it, its very common with patrols.
Check all your suspension bushes and wheel bearings, replace if needed, get a wheel alignment and tire balance.
If that doesn't fix it then check king pins and adjust by removing top and bottom spacers
If that doesn't fix it then check king pins and adjust by removing top and bottom spacers
GQ Patrol Wagon, 6 point roll cage
351 cleveland, CHI heads, solid cam, Funnelweb single plane, 750 HP DP
351 cleveland, CHI heads, solid cam, Funnelweb single plane, 750 HP DP
as bogged said theres a million threads on this but the first thing i would check (am i speaking from personal experience after spending heaps on tyre change and front end bits and pieces)
i would check the chassis where your steering box bolts up!
after nearly rebuilding the whole damn front end n new tyres we found that the chassis where the steering box bolts on had a crack which was hard to see but was very much so there!
good luck!
i would check the chassis where your steering box bolts up!
after nearly rebuilding the whole damn front end n new tyres we found that the chassis where the steering box bolts on had a crack which was hard to see but was very much so there!
good luck!
[color=lime][b]Im not a gyno but ill take a look at it for you![/b][/color]
If your wheel bearings are loose there is an easy permanant fix for that.
MQ and GQ wheel bearing hubs are the same as GU.
MQ and GQ use a flat washer between 2 nuts that has tabs you fold over. That washer flogs out easy if the bearings have been tightened before. You need to replace that washer with a new one from Nissan as the centre tab on it slides inside the stub axle thread and causes the wheelbearings to undo.
On the other note.... you have the option to piss off all that rubbish all together and use the system in the GU's.
The GUs utilise 1 round nut with holes in it and then another thick washer plate over the top and 2 screws go into the first washer to hold it all there. It can never come loose and is much easier to torque up and undo. All in all a major design improvement.
The best part is they work in all MQ and GQs as well. Ive gone to nissan and swapped those bits out in every one ive owned. I think Nissan only stung me about $70 to buy both sides last time i did it.
cheers
Screwy
MQ and GQ wheel bearing hubs are the same as GU.
MQ and GQ use a flat washer between 2 nuts that has tabs you fold over. That washer flogs out easy if the bearings have been tightened before. You need to replace that washer with a new one from Nissan as the centre tab on it slides inside the stub axle thread and causes the wheelbearings to undo.
On the other note.... you have the option to piss off all that rubbish all together and use the system in the GU's.
The GUs utilise 1 round nut with holes in it and then another thick washer plate over the top and 2 screws go into the first washer to hold it all there. It can never come loose and is much easier to torque up and undo. All in all a major design improvement.
The best part is they work in all MQ and GQs as well. Ive gone to nissan and swapped those bits out in every one ive owned. I think Nissan only stung me about $70 to buy both sides last time i did it.
cheers
Screwy
TUFF TRUCK TEAM OPPOSITE LOCK Proudly Sponsored By:
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
get a tough dog adjustable steering dampner, there great, dont get a return to centre dampner, as they are absolute shitPIG_GQ wrote:Ha ha. It turns out the wheel bearings were loose did them up abit and all is good now thanxs for all the ideas.......Can anyone recomend a good steering damper and clutch kit
In my lifted GQ shorty i have no need for a RTC dampener as it handles well.....RIZZO wrote:get a tough dog adjustable steering dampner, there great, dont get a return to centre dampner, as they are absolute shitPIG_GQ wrote:Ha ha. It turns out the wheel bearings were loose did them up abit and all is good now thanxs for all the ideas.......Can anyone recomend a good steering damper and clutch kit
Though im wondering whats so bad about RTC dampeners? ive used them on at least a few previous trucks and i think they work very well. The only thing i can say about them is they cause the power steering to be heavier but thats no big deal....
Screwy
TUFF TRUCK TEAM OPPOSITE LOCK Proudly Sponsored By:
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
I did the same GU hub nut conversion as Screwy, i paid $54 for both sides (2 nuts, 2 washers and the 4 screws) from highway nissan at slacks creek. Stopped me having to tighten them up every 2000 kms after i took them off to change the brakes.Screwy wrote:If your wheel bearings are loose there is an easy permanant fix for that.
MQ and GQ wheel bearing hubs are the same as GU.
MQ and GQ use a flat washer between 2 nuts that has tabs you fold over. That washer flogs out easy if the bearings have been tightened before. You need to replace that washer with a new one from Nissan as the centre tab on it slides inside the stub axle thread and causes the wheelbearings to undo.
On the other note.... you have the option to piss off all that rubbish all together and use the system in the GU's.
The GUs utilise 1 round nut with holes in it and then another thick washer plate over the top and 2 screws go into the first washer to hold it all there. It can never come loose and is much easier to torque up and undo. All in all a major design improvement.
The best part is they work in all MQ and GQs as well. Ive gone to nissan and swapped those bits out in every one ive owned. I think Nissan only stung me about $70 to buy both sides last time i did it.
cheers
Screwy
Its a very good and easy upgrade.
Cheers Adam
LWB GQ (Sharleen) RIP
1995 GQ LWB ST (Elizabeth) + some fun stuff
1995 GQ LWB ST (Elizabeth) + some fun stuff
correct me if i'm wrong but the problem with the rtc dampners is the bore is a lot smaller than normal. And besides that if your tyres wont return to centre than your steering and suspension is out. Basically they mask the problem. JMOVanne wrote:I was gonna buy a RTC damper today, so there shit?
4INCH EFS LIFT
SUPRERIOR ARMS
TWIN LOCKERS
11000LB tigerz11 WINCH
36 swampers OFF ROAD
3inch S/S/S exhaust
SUPRERIOR ARMS
TWIN LOCKERS
11000LB tigerz11 WINCH
36 swampers OFF ROAD
3inch S/S/S exhaust
They are a cheap and easy 'get you out of trouble' when your rig is heavy comp, not often on the road or you have dramas but cant afford to sort them out..............
As said above, ive used them before for different applications and may use them again. They have there own place in the market.
Screwy
As said above, ive used them before for different applications and may use them again. They have there own place in the market.
Screwy
TUFF TRUCK TEAM OPPOSITE LOCK Proudly Sponsored By:
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
RTC are a waste of money. Fix your geometry, bearings and rubber bushes, and put a decent steering damper on and you should have no dramas.
What's the difference between ignorance and apathy? I don't know and I don't care.
I am an insomniac dyslexic agnostic. I often lay awake all night wondering if there really is a Dog.
I am an insomniac dyslexic agnostic. I often lay awake all night wondering if there really is a Dog.
few things to check wheel bearings, pan hard bushes, trialing arm bushes, tie rod and if you have enough carster and check if you have water in your tyre i had the same problem and could not find it then i looked in my tyres and they had water in them
need some plumbing done? cashies top quality job for cheaper south east melbourne Daniel 0423771198
Master of my own domain
All 4 had water? or just one?striga22 wrote:few things to check wheel bearings, pan hard bushes, trialing arm bushes, tie rod and if you have enough carster and check if you have water in your tyre i had the same problem and could not find it then i looked in my tyres and they had water in them
Some people purposely put water in their tyres.
Exactly ..............[gubeaut] wrote:correct me if i'm wrong but the problem with the rtc dampners is the bore is a lot smaller than normal. And besides that if your tyres wont return to centre than your steering and suspension is out. Basically they mask the problem. JMOVanne wrote:I was gonna buy a RTC damper today, so there shit?
Who is online
Users browsing this forum: No registered users and 2 guests