what have people built for their custom aframes ?
i was thinking of using a trailer stub axle and base the joint around that or am i better raiding one out of a rover?
this is for my scat project so im on a tight budget
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
a frame joint?
Moderators: toaddog, TWISTY, V8Patrol, Moderators
a frame joint?
thanks jono
Skip 1995 tdi disco the new tourer
Tin Worn the scat crawler with charade (fwd) motor and auto patroll transfer and locked yota diffs all for under $1000
Skip 1995 tdi disco the new tourer
Tin Worn the scat crawler with charade (fwd) motor and auto patroll transfer and locked yota diffs all for under $1000
Re: a frame joint?
IF you're on a budget, then a Rover A-frame, ball joint and axle mount from a Salisbury axle is cheap. You'll just need to build a mount on the ale for the ball joint mount.hillbilliywheelchair wrote:what have people built for their custom aframes ?
i was thinking of using a trailer stub axle and base the joint around that or am i better raiding one out of a rover?
this is for my scat project so im on a tight budget
[/img]Cheers
Slunnie
Discovery TD5, Landy IIa V8 ute.
Slunnie
Discovery TD5, Landy IIa V8 ute.
Yes, the A-frame and ball joint are the same, but the Salisbury diff has a little plate that the ball joint plugs in to and will tighten up on. That plate is then easy to bolt onto the axle housing. Its a lot easier to bolt that on than trying to fabricate a tapered hole in a mount like how the Rover axles are done. You can see in the top pic the holes that I've drilled out to take the mount and then the mount in place in the bottom pic.hillbilliywheelchair wrote:sunnie any reson from a salabery over a rover diff?
and good idea to use the whole shebang it'll make life easy
I then just made a cross member for the A-frame to mount to.
Cheers
Slunnie
Discovery TD5, Landy IIa V8 ute.
Slunnie
Discovery TD5, Landy IIa V8 ute.
No build thread on that one.
Here are the pics of the coiling of that series. Not too long after the suspension was coiled that chassis was scrapped as I found some rust in it that made it useless.
http://www.slunnie.com/coppermine/thumb ... ?album=100
Here are the pics of the coiling of that series. Not too long after the suspension was coiled that chassis was scrapped as I found some rust in it that made it useless.
http://www.slunnie.com/coppermine/thumb ... ?album=100
Cheers
Slunnie
Discovery TD5, Landy IIa V8 ute.
Slunnie
Discovery TD5, Landy IIa V8 ute.
A Frame knuckle , totally greasable , manufactured by Glen Dobbin , Weld and gusset centre tube to top of diff , weld swivel joint onto a frame , as seen on glen dobbins Tuff Truck , brand new , got one if interested , Cheers Paul.
BLOWNZUK 1.3 efi,sc14 supercharger,hilux diffs,detroit lockers,stage 4 rockhopper,6 point cage,35 muddies.
Who is online
Users browsing this forum: No registered users and 151 guests