Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Shorty Noise

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Forum rules
Post Reply
Posts: 57
Joined: Tue May 15, 2007 6:56 pm
Location: Tamworth

Shorty Noise

Post by mattman »

Any suggestions .... weird noise at about 90-100 kph if i throttle of a little or put foot on clutch. Its a growling noise much like a bearing but have done frts and rears, axles are straight. running out of ideas wondering if any one has come across anything like this before
cheers
Top
Posts: 103
Joined: Sat Dec 19, 2009 9:27 pm
Location: Ipswich

Post by tufftruckin »

does it sound like when you drive over the audible lines on the highway? my ute does the same thing , i have tried changing tyres drive shafts, ect soon to get diff gears lapped when the locker goes in! hoping it will go away!
An ounce of precaution is better than a ton of cure!
Top
Posts: 140
Joined: Sun May 18, 2008 4:24 pm
Location: bogged in a hole near you

Post by BeNoS »

what sort of lift you running? is it a swb or wagon.
could be tailshaft vibes/grumbles. make sure your uni joints are on the same angle and go from there.
Top
Posts: 4330
Joined: Tue Jun 08, 2004 6:06 pm
Location: Central Victoria

Contact:
Contact coxy321

Post by coxy321 »

BeNoS wrote:what sort of lift you running? is it a swb or wagon.
could be tailshaft vibes/grumbles. make sure your uni joints are on the same angle and go from there.
x2

I get these noises between 80-100km/h, and its because i have no castor correction on the rear diff and a 4" lift.
Top
Posts: 36
Joined: Sun Apr 06, 2008 7:15 pm
Location: chelsea heights

noise

Post by jabs »

x3
had the same problem in my shorty its an easy fix just need to get some gearbox spacers ARB sell em it will drop the crossmemberdown a touch so your unis are a little more straight dont go to extreme with this though as it will f@#k your enine mounts if you go to low
Top
Posts: 4330
Joined: Tue Jun 08, 2004 6:06 pm
Location: Central Victoria

Contact:
Contact coxy321

Post by coxy321 »

Or buy these to get the correct angles between the unis at each end of the tailshaft:

http://www.superiorengineering.com.au/p ... cts_id=856

http://www.superiorengineering.com.au/p ... cts_id=854
Top
Posts: 65
Joined: Thu Jul 12, 2007 5:32 pm
Location: cobden

control arms

Post by stevejl »

Most of you are right lenghten your lower control arms about 16mm to 20mm to get the flange on the back of the transfer and the flange on the diff the same or get a double cardenal joint
Top
Posts: 1345
Joined: Wed Jul 18, 2007 7:15 pm
Location: Jimboomba

Post by SIM79 »

I had the same problem with my SWB, replaced my lowers arms with longer arms, got adjustable uppers, replaced my unis, swapped my drive shaft 180*, 15mm gear box spacers, this all did nothing nothing to stop the grinding noise.
I pumped my drive shaft spline with grease, this almost made the grinding stop but it only lasted for about an hour.
I then went to buy a driveshaft spacer from snake racing and they didn't want to sell me one as they said it wouldn't work. I did search on outers and found someone that tried it and it didn't work.

I did a high pinion rear and it worked no more grinding noises!!!!!
Nitto Mud Grapplers, Lockrite, 4.3s, Trail Ready BL, PTO, High pinion rear,Gu diff with Buds Customs armour and heaps of Superior gear, 24% Reduction .
Top
Post Reply

Return to “Nissan”

Who is online

Users browsing this forum: No registered users and 5 guests