Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

pyro guage from group buy problems..

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 218
Joined: Thu Jun 26, 2008 6:41 pm
Location: Bundy, QLD

pyro guage from group buy problems..

Post by rumpig89 »

gday

i got a green display digital pyro guage from that group buy late last year and it has been running fine until about 3 weeks ago.

Now it spends most of its time just displaying "EEEE". When i touch the casing it sometimes displays the reading... othertimes nothing. Sometimes it will read properly for a couple of hours, sometime in 3 second bursts, sometimes nothin...

anyone had an similar problems or know what it might be??

matt
Top
Posts: 1380
Joined: Tue Mar 18, 2008 11:40 am
Location: Perth, WA

Post by bakerboy »

E for earth? grounding out when you touch it?
mike_nofx wrote:Is "Athol" what people with a lisp call him??
RAY185 wrote:I think it's delightful! So does my wife Bill.
Top
Posts: 31
Joined: Thu Jul 07, 2005 7:39 pm
Location: brissy

Post by 110county »

I got a couple of these at the same time (boost and pyro) and found that the tech support (via email) was great when I had programing problems with mine. I would go straight to auberins by sending them an email, I always got a fast answers that solved all my problems.


Luke
95 factory turbo diesel 80 series

A member of the 1HDFT fan club
Top
Posts: 302
Joined: Sun Feb 04, 2007 8:37 pm
Location: Bendigo

Post by krusty182 »

Symptoms sound a lot like a loose connection or intermittent open circuit on your probe wiring.
---> insert witty remark here <---
Top
Posts: 2585
Joined: Fri Mar 28, 2008 4:45 pm
Location: SYDNEY

Post by thehanko »

mine did that when my probe wires got damaged.

to check your unit you short out the two terminals which your pyro would screw into and it should show approx air temp of that day. if so something is wrong with your probe.

other wise its your unit.

for me i had damaged my probe and it was sorted.
*there's a rock, drive over it :) there's a bigger rock, drive over it :twisted: there's an even bigger rock, oops broke it :oops: Upgrade broken bit :bad-words:
Goto *
Top
Posts: 218
Joined: Thu Jun 26, 2008 6:41 pm
Location: Bundy, QLD

Post by rumpig89 »

cheers ill have a better look into it when i get it back from the shop... getting new clutch.
Top
Posts: 80
Joined: Thu Jul 20, 2006 11:40 pm

Post by danaz »

I have the green screen unit an had problems with mine too. My temperature was fluctuating all over the place and showing EEEE too, I sent it back for warranty and had it returned within a week of them receiving it. It had a 'cold solder' point as they called it, I assume a connection not made properly. They said they hadn't seen the problem before but maybe you got a bad one from the same batch as mine? As said, short out the terminals on the back (the manual tells you which ones) and if the display doesn't show ambient the problem is with the display unit not the probe. I was dissapointed with the failure but I must say their after sales service through email was fantastic.
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 102 guests