Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

40 series 350 chev carby to efi throttlebody conversion

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Post Reply
Posts: 48
Joined: Wed Aug 12, 2009 8:50 pm
Location: townsville

40 series 350 chev carby to efi throttlebody conversion

Post by woodyjbh »

Guys n gals,

Im currently running a carby fed 350 chev in my 40 and im looking at converting it to efi for some better drivability offroad.

Im hoping to keep things fairly simple so Im looking at an efi throttle body which will just sit in place of the holley carby I currently have. Something similar to this:

http://www.efihardware.com/products/c96 ... tle-bodies

I currently have an HEI dizzy and a 600 Holley running off an electric pump at 6 psi.

But i've got a few questions i'm hoping someone can help me with...

*Im aware I'll have to buy a computer to run the system. Can I run fuel only, utilising my HEI dissy and, if so, are there any recommendations on which computer??

*What other parts do i need to purchase to get this running?? I know I need an EFI fuel Pump, High pressure lines and injectors but what else do I need to consider??

* What would be a reasonable budget for something like this?? I know I can pick up the throttle body for approx $700. Computer will be around $1000. Injectors will be around 100-150 each. I can fit it myself but will need it tuned. Is 3 grand enough??

Cheers in advance...

Woody
Posts: 348
Joined: Sun Aug 23, 2009 9:55 am
Location: Brisbane

Post by VooDoo »

Here ya go

http://www.eficonnection.com/eficonnection/default.aspx

You can use the LS1 PCM, coilpacks and loom and the gear from those guys to generate the signal. No Dizzy required.

PCM is around $100, coilpacks off ebay are often $150ish and the kit from those guys for $500. Stock injectors $100 a set. Prob get away with it fully fitted and tuned for under $2k.

IM not connected to those guys buy i do know the LS1 stuff pretty well.
Posts: 1208
Joined: Fri Nov 08, 2002 8:21 pm
Location: sunshine coast

Post by killalux »

I would also recomend the LS1 kit from efi connection. They are great guys to deal with and fast service. i use them a fair bit for connectors.

You would want to budget $900 for a new standalone engine harness to suit the ls1 pcm. also allow for a tune as it won't run real well with the factory ls1 tune. Should pick up a factory ls1 manifold pretty cheap. Will be a much more efficient setup then a throttle body injection, and you get rid of the dizzy.
Would be able to get it done for $3000 i would think.
Steve
KILLA KUSTOM KABLES
CUSTOM AUTO ELECTRICAL SPECIALISTS
0404811498
LS1 & DURAMAX ENGINE CONVERSIONS, DRIVE IN DRIVE OUT. PATROLS AND CRUISERS

LS1 STANDALONE HARNESS $475ex
Posts: 1768
Joined: Sun Mar 14, 2004 11:51 am
Location: Weipa

Post by crankycruiser »

I have a std ls1 manifold with injectors and fuel rails sitting here if u are interested, no throttle body tho.
80 xtra cab
Supercharged LS1, Locked n shit

80 Wagon, TD Tourer, locked, Interco 35s, G turbo
Posts: 35
Joined: Sun Jul 12, 2009 11:55 am
Location: Perth

Post by Seth »

Mate check out a Powerjection set up they are supposed to be pretty good. One of the Hot Rod mage just done a write up on putting one on a 351 Cleveo. Anyways google em and see what ya think.
Posts: 348
Joined: Sun Aug 23, 2009 9:55 am
Location: Brisbane

Post by VooDoo »

crankycruiser wrote:I have a std ls1 manifold with injectors and fuel rails sitting here if u are interested, no throttle body tho.
LS1 manifolds dont come close to fitting a LT1. Better off drilling the stock manifold for the injectors and fab some rails unless you can find a kit to suit. Need to get the injectors as close to the ports as you can and angled towards the valve for best flow. There are some weld in injector bungs around too.
Posts: 238
Joined: Mon Oct 18, 2004 3:44 pm

Post by devo »

check out yank ebay
stuff like this
lt1 manifold, throttle, injectors etc us$250
just bolt it on and use the ls1 computer
http://cgi.ebay.com/ebaymotors/95-CHEVR ... _500wt_956
Posts: 16934
Joined: Sun Oct 20, 2002 6:57 pm

Post by RUFF »

Seth wrote:Mate check out a Powerjection set up they are supposed to be pretty good. One of the Hot Rod mage just done a write up on putting one on a 351 Cleveo. Anyways google em and see what ya think.
Holley Projection?

I had this set up on a 5lt VL once. Engine had cam,heads and extractors. Went well and had no issues at all. Its a simple bolt on and go set up. You dont need a computer to tune it. Although for best results a dyno would be advised.

I have heard both good and bad reports on this set up. But in my experiance it ran perfect.
Posts: 5256
Joined: Fri Jun 16, 2006 6:49 pm
Location: Melbourne

Post by Struth »

One of our guys runs this setup on a warm 308,


Image

Image

Image

Image

The computer is built into the throttle body and connects to a laptop via a USB style lead.

Comes with basic parameters to choose for your type of engine and can be fine tuned by laptop from there.

Alternatively the supplier can connect to your motor via you laptop over the net and assist by remote tuning.

Not sure what it cost but I think about $3k.

Cheers
Posts: 35
Joined: Sun Jul 12, 2009 11:55 am
Location: Perth

Post by Seth »

Yeh i just ordered one for my Hilux and it was $3179 inc GST
Posts: 48
Joined: Wed Aug 12, 2009 8:50 pm
Location: townsville

Post by woodyjbh »

Guys,

The powerjection seems like just the thing I was chasing. Where did you guys order them from?? Is it gonna be better to order from the US or are there some places in Aus that stock/sell them??

I've done some googling but not found anything concrete...

Woody
Posts: 5256
Joined: Fri Jun 16, 2006 6:49 pm
Location: Melbourne

Post by Struth »

User avatar
RN
A speed camera would have prevented that!
Posts: 15822
Joined: Sat Feb 05, 2005 3:46 pm
Location: Check your six.

Post by RN »

http://www.retrotekspeed.com/products/p ... ystem.html

$1750 USD in 2009.

Our dollar has slumped a bit in the meantime. :shock:
I am the Nightrider! I am the chosen one. The mighty hand of vengeance, sent down to strike the unroadworthy!
Posts: 5256
Joined: Fri Jun 16, 2006 6:49 pm
Location: Melbourne

Post by Struth »

I wonder what the difference is between the 4 systems/part numbers, different price but same description for each?

$1795 is very cheap for a tuneable injection system.

Cheers
Posts: 238
Joined: Mon Oct 18, 2004 3:44 pm

Post by devo »

the 4 product descriptions are different. satin/polished finish. with/without fuel system
Posts: 619
Joined: Thu Nov 03, 2005 11:20 am
Location: vic

Post by Hamo »

killalux wrote: and you get rid of the dizzy.

Steve
I dont think (on old school 350's) that you can get rid of the dizzy as it drives the oil pump no dizzy no oil presure
[quote="RN"]So do you support your local vendor...not if it is going to cost me almost double. [quote]
Posts: 765
Joined: Fri Mar 12, 2010 7:28 pm
Location: Fixing something else the kids have broken

Post by BadMav »

I'm looking at putting the EA Falcon single point throttle body injection on my TB42, not sure if they flow enough CFM for a 350 chev tho, but maybe worth a look see?
Don't take life too seriously...it isn't permanent.
Posts: 109
Joined: Fri Jul 01, 2005 6:44 pm
Location: broken hill

Post by gouldy »

http://www.holley.com/types/Avenger_EFI ... ystems.asp

Plenty of Holley retailers in Australia
GQ. Supercharged LSX 427, 500rwkw. camtech cam,90mm Holley Throttle Body. twin 4"exhaust, big fuel system, King bypass shocks and bumpstops.
Posts: 231
Joined: Tue Sep 14, 2004 1:11 pm
Location: Melbourne

Post by leehamescort »

G'day,

I've got the powerjection 3 in the pics.

Supposedly there is a new model out ow Powerjection 3 Pluc which also has spark control as part of the system.

Mine cost me about $3000 from the austalian distributor (Australian Auto Accessories, in nunawading 9845 0800)

The manufacturer tells me it 100% waterproof and can be run under water (computer is mounted to the throttlebody and is totally sealed)

You can get it cheaper direct through the USA but i figured i'd pay the extra and if i had any dramas i had local support.

Mad a huge difference to drivability of the car.
Kit came with everything and was a one weekend install and go through the pre flight checks, turn the key and it fired straight up.

Ran super rich till it self tuned and now drives well, just hoping to do a few tweaks to the map to get it running a bit more efficient but overall I'm very happy with it.

It's self tune has been better than the $3000 i've spent of dyno tunes trying to get the carby setup to run right. Should have gone this way from the start and i'd have a lot more cash in my wallet!!

catcha
leeham
Bloody IFS bugger who slows down the SAS boys.
www.vickrawlers.com
Posts: 48
Joined: Wed Aug 12, 2009 8:50 pm
Location: townsville

Post by woodyjbh »

Thanks heaps for the info guys.

I've passed on the details of both the powerjection and the holley avenger EFI system to my local performance shop and their chasing down prices for me. I'll post up and update when i've got them.

Cheers,

Woody
Post Reply

Who is online

Users browsing this forum: No registered users and 13 guests