Don't know if this has been done before. But what about a thread with tips & contributions from those who have done the extra cab or dual cab.
I reckon there would be a lot of points that would be helpfull to budding builders
Johno
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
How About Tips For Extra Cab Build
-- measure 100 times only cut once!
-- always allow a bit extra for trimming sheet metal after lining it up!
-- plan in advance on how you want the look!
-- build your own tray (its not that hard) maybe a trip to local tray builders and take some pics if they allow!
-- try sorce your materials for tray same place as tray builders!
-- dont use window out of another ute, prety cheap to cut your desired hole and get machinery glass place to cut fit and stamp new one!
-- use back section and move it forward for nicer factory look!
-- talk to engineer before you start and ask him what he wants i.e baby seat anchor points, bracing etc
-- in most cases for drilling etc buy your own bits and drill etc to save on paying someone else to do it
-- source a good local powder coater and suck up his date for cheap powder coating
-- if some one close to you or reasonably close has already done one go check it out and ask questions in person as to whats involved!
and most importantly (other than keep the missis serviced quite often so as to not get in the shit for the amount of time you will spend on it) MAKE SURE YOU COVER AREAS WHERE YOU ARE GRINDING VERY VERY WELL OR YOU WILL END UP SETTING SHIT ON FIRE!
YES I DID A COUPLE OF TIMES!
oh yeh and also dont wear tracky dacks cause youl catch on fire there aswell (i did) stuffed around 5 pairs and 5 shirts!
and dont wear loose Tshirts either cause its not fun when they catch on fire or worse get stuck into grinder
other than the above suck some piss, grind and weld yah heart out!
-- always allow a bit extra for trimming sheet metal after lining it up!
-- plan in advance on how you want the look!
-- build your own tray (its not that hard) maybe a trip to local tray builders and take some pics if they allow!
-- try sorce your materials for tray same place as tray builders!
-- dont use window out of another ute, prety cheap to cut your desired hole and get machinery glass place to cut fit and stamp new one!
-- use back section and move it forward for nicer factory look!
-- talk to engineer before you start and ask him what he wants i.e baby seat anchor points, bracing etc
-- in most cases for drilling etc buy your own bits and drill etc to save on paying someone else to do it
-- source a good local powder coater and suck up his date for cheap powder coating
-- if some one close to you or reasonably close has already done one go check it out and ask questions in person as to whats involved!
and most importantly (other than keep the missis serviced quite often so as to not get in the shit for the amount of time you will spend on it) MAKE SURE YOU COVER AREAS WHERE YOU ARE GRINDING VERY VERY WELL OR YOU WILL END UP SETTING SHIT ON FIRE!
YES I DID A COUPLE OF TIMES!
oh yeh and also dont wear tracky dacks cause youl catch on fire there aswell (i did) stuffed around 5 pairs and 5 shirts!
and dont wear loose Tshirts either cause its not fun when they catch on fire or worse get stuck into grinder
other than the above suck some piss, grind and weld yah heart out!
[color=lime][b]Im not a gyno but ill take a look at it for you![/b][/color]
Who is online
Users browsing this forum: No registered users and 0 guests