Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Will a 2H and 60ser bellhousing fit a 45

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Forum rules
Post Reply
Posts: 1042
Joined: Mon May 05, 2008 6:33 pm
Location: MACKAY

Will a 2H and 60ser bellhousing fit a 45

Post by SIMMO84 »

As above have a 45 that has a 5.0 and adapter that I need d to put the 2h into. Main concern is if the 60 bellhousing has holes to bolt the gear box mounts to. Would have a look but its 80km away and im not going back up until I go to swap motors.
Wtb, 105 series rear tyre carrier, alloys and tyres.
Top
Posts: 765
Joined: Fri Mar 12, 2010 7:28 pm
Location: Fixing something else the kids have broken

Post by BadMav »

I put a 75 series 5 speed into my 45 and it bolted straight in. I believe they are the same size clutch (don't quote me on that) and same spline. Mine had an ED Falcon 4.0 litre in it with adaptor plate to the original BH. About the gearbox mounts on the BH, don't use those ones. Make your own gearbox cross member. They will rip out a big hole in the bell housing when they fail. Trust me.
Don't take life too seriously...it isn't permanent.
Top
Posts: 7
Joined: Mon Apr 16, 2007 10:27 am
Location: mornington peninsula

Post by betsy »

i also belive they are the same iv just done a 45 to 75 engine swap with no problems they run the same spline as a 60 iv been told good luck
75s troopy 1hz. 33,claws .air lockers 3' lift ./ 75s ute 6x6 35,claws .3 air lockers . spring over . 6.5 chev diesel ./ fj45 1968 ute 6x4 air lockers 33,claws 454 chev ...WANTED 75s ute tubs any cond
Top
Posts: 1042
Joined: Mon May 05, 2008 6:33 pm
Location: MACKAY

Post by SIMMO84 »

Yeah i just need the engine in the 45 as I want the 5.0 for my hilux. Does the 60 bellhousing have the bolt holes for the gbox mounts? Its not my 45 so I dont want to spend too much time on it.
Wtb, 105 series rear tyre carrier, alloys and tyres.
Top
Posts: 765
Joined: Fri Mar 12, 2010 7:28 pm
Location: Fixing something else the kids have broken

Post by BadMav »

No, the 60 gearbox has a proper cross member under it unlike the 45 box being solely supported by the bell housing. You may be able to graft in a 60 series cross member perhaps? Depends on how bad you want the engine.
Don't take life too seriously...it isn't permanent.
Top
Posts: 1042
Joined: Mon May 05, 2008 6:33 pm
Location: MACKAY

Post by SIMMO84 »

ill get the right bell housing if I need to. I want to keep the 60 cross member for the hilux.
Wtb, 105 series rear tyre carrier, alloys and tyres.
Top
Posts: 441
Joined: Sun Nov 07, 2004 2:25 pm
Location: Rockhampton

Post by hj 45 »

Find a wrecked 40/42/45/47 with a build date of August 1980 onwards, it'll have the right gearbox crossmember, rip it out and the brackets that connect it to the chassis rails.
Top
Post Reply

Return to “Cruiser / Prado”

Who is online

Users browsing this forum: No registered users and 3 guests