hey guys i have recently in the last 2 to 3 months sheared the studs outta the rear hubs on my 60 causing the axle to pop out and there for no rear wheel drive
the first one happened ages ago got aanother hub fitted up all sweet then the 2nd one just last weekend so done the same but now ive changed both sides and makes me wonder why it did it? i run 35"s and i no its extra strain is there any solution to making it stronger?
me and my dad were talking about it maybe getting the hub drilled out so i can fit bigger studs for the axle in less chance of breakage?
any suggestions as dont want this to keep happenenin i no its the result of bigger tyres but yer
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
60 series rear hub
Moderators: toaddog, Elmo, DUDELUX
60 series rear hub
brentz
TUF-60 starting build soon
TUF-60 starting build soon
Re: 60 series rear hub
Do you have an auto locker in the rear? I hear they can make the issue worse. Are you reguarly checking the tension on the studs? Wheel bearings in good condition?
The Silver Bullet - BJ74
Where the actions at Ontrack 4wd Club
http://www.ontrack4wdclub.com/
[url]http://www.cams.com.au/[/url]
Where the actions at Ontrack 4wd Club
http://www.ontrack4wdclub.com/
[url]http://www.cams.com.au/[/url]
Re: 60 series rear hub
Upgrading the studs has been done plenty of times in the past mate. Two ways that I have seen it done is to use the 10mm studs off a 100 series or use 3/8 bolts high tensile bolts. I ended up doing the 3/8 bolts first, without a problem and then went to 3/8 cap screws because they are stronger again/can be tightened more.
edit: I think hulsty used caps screws to replace the standard studs, which is another option.
edit: I think hulsty used caps screws to replace the standard studs, which is another option.
Braden Tagg of XRO Racing is scum and not to be dealt with. See here http://www.outerlimits4x4.com/viewtopic.php?f=10&t=223295
bj73 build up thread http://www.outerlimits4x4.com/ftopic168809.php
bj73 build up thread http://www.outerlimits4x4.com/ftopic168809.php
Re: 60 series rear hub
hulsty nah i dont have a locker and the first one i wasnt checking the tension ill admit but the second one i was then one day noticed 3 studs snapped so yer
sprungupcruiser thanks for that mate ill give that a shot did you just drill and tap them? also did just drill the holes bigger in the axle?
sprungupcruiser thanks for that mate ill give that a shot did you just drill and tap them? also did just drill the holes bigger in the axle?
brentz
TUF-60 starting build soon
TUF-60 starting build soon
Re: 60 series rear hub
Yeah mate, I just did it carefully with a cordless drill, but thats rough. It would be best with a drill press. I did just drill the axle holes out to 3/8th, if you go with the 10mm studs and use the cone washers then you will need to machine out the axle for the bigger cone washer aswell.
Braden Tagg of XRO Racing is scum and not to be dealt with. See here http://www.outerlimits4x4.com/viewtopic.php?f=10&t=223295
bj73 build up thread http://www.outerlimits4x4.com/ftopic168809.php
bj73 build up thread http://www.outerlimits4x4.com/ftopic168809.php
Re: 60 series rear hub
okay thanks for that mate helps heaps i got two spare hubs now that have broken studs so ill give that a shot thanks again
brentz
TUF-60 starting build soon
TUF-60 starting build soon
Who is online
Users browsing this forum: No registered users and 1 guest