Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Advice on EGT readings - 1HD-T

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Post Reply
Posts: 23
Joined: Wed Mar 25, 2009 1:16 pm
Location: Brisbane

Advice on EGT readings - 1HD-T

Post by DaveHDJ80 »

Hi,

I have just fitted an ENG-TEK digi pyrometer to my 80 series. Looks to me to be running pretty hot - opinions please!

Its a 1HD-T with beaudesert 3inch exhaust.

Injector pump rebuilt 125k ago prior to my ownership. Injectors done at same time.

I was told the pump was running standard settings and factory boost level.

Just did a short trip with the pyro with only a smallish load - 13ft tinnie, swags, engel, 3 ppl. - not a lot of gear really.

Running 305/70/16s.

Temps (EGT) as follows. therocouple is after the turbo in the dump pipe. Dump pipe internal diameter is 3.5inch. in degrees celcius.

Idle after running - 170

Flat road 100km/h 350 - 400.

5th gear slight hill - 450 - 500.

Highest reading was 530.

Without any gear at all, and accelerating from 60 - 100 in th gear It rised all the way to 520 before dropping back at about 90-95 and tapering down.

I havent run a boost guage yet, but seems like someone has played with the settings.

Does go bloody well though, but ive never driven another 1HD-T to compare.
Last edited by DaveHDJ80 on Sun Oct 10, 2010 8:15 pm, edited 1 time in total.
Posts: 549
Joined: Mon Oct 28, 2002 11:53 am
Location: Sydney

Re: Advice on EGT readings - 1HD-T

Post by slowhilux »

That sounds about right. My FTE towing 1300kg, total of about 4500kg, reads similar to yours, but it is intercooled. Headwind, fully loaded and towing @ 110km/h sits on about 380-420deg C, in 40 deg C ambient temp
Phill
1995 DX 80 series, brought to you by:- 1HDFTE, A750, PWR, Secret Squirrell Steinbauer, BFG, GME, Engel, ARB, Kaymar, and my empty wallet!
Posts: 288
Joined: Sat Mar 18, 2006 4:30 pm
Location: Darwin

Re: Advice on EGT readings - 1HD-T

Post by jsttry »

Similar to my 1HD-T which has been tuned and running 12psi.
Posts: 23
Joined: Wed Mar 25, 2009 1:16 pm
Location: Brisbane

Re: Advice on EGT readings - 1HD-T

Post by DaveHDJ80 »

Thanks,

So just to confirm slowhilux - is your FTE running standard fuel boost settings?

So similar reading on 1HD-T with 12psi would indicate that my fuel boost settings are NOT standard.

Are these temps ok?

I have set the alarm on pyro to come on at 550 and off at 500.

Thanks for the help.
Posts: 986
Joined: Tue Nov 11, 2008 7:17 pm
Location: Brisbane

Re: Advice on EGT readings - 1HD-T

Post by TheBigBoy »

Mine sits on 270 at 100kph. Towing a 1.5 tonne builders trailer the most it has ever reaches was 470 flat up a hill.

Stock as rock 1HDT with exhaust and dump pipe. 165 000k's on it. Not tuned blowing black smoke.
Posts: 23
Joined: Wed Mar 25, 2009 1:16 pm
Location: Brisbane

Re: Advice on EGT readings - 1HD-T

Post by DaveHDJ80 »

Thanks - thats what i thought. I reckon a stock 1HD-T would be much lower.

I am a bit worried that the settings will be too much for a big load - i.e. towing my big boat up Fraser island fully loaded.

Next step would be to check boost I guess.

In comparison, have just been up to fraser in a mates 1HZ turbo with top mount intercooler running 12psi and even with a heavy load we never saw 400 degrees. Highway it sat around 270.
Posts: 3740
Joined: Sat May 26, 2007 5:04 pm
Location: Licking a window near you

Re: Advice on EGT readings - 1HD-T

Post by 80's_delirious »

test it with a bit of a load, 3rd or 4th gear up a decent hill. Hold it with wide open throttle for a hill climb starting from around 2000RPM at the bottom and push it through to redline before you reach the top. Watch the EGTs through out the climb.

Peak EGTs will be seen when the engine is under load, full throttle. Excess fuel creates more heat in the exhaust gases. test as above and you are giving it max fuel, but it is working to get enough air through it.

standard tune varies from one car to another.

It is regarded as more accurate and reliable to have the thermocouple in the manifold before the turbo

A boost gauge would be helpful also. More boost (within limits) with the same fuel settings should reduce the EGTs, more boost = more airflow, so lower A/F ratio, so less heat.

Your engine will see peak EGTs only a small percentage of the time, with an EGT gauge you can monitor this in circumstances like towing up a long hill, and drive according to the gauge.
Short bursts of high EGTs (ie passing on a hill) wont destroy the engine, prolonged running at high EGTs will (ie towing a boat in 4th up a long hill)

depending on your threshold for hip pocket pain, leave it tuned up, and enjoy the power, and drive it to the gauge when you are working it hard
RN wrote:pussy is out, its the log for me... Thank you Jesus.
Posts: 23
Joined: Wed Mar 25, 2009 1:16 pm
Location: Brisbane

Re: Advice on EGT readings - 1HD-T

Post by DaveHDJ80 »

Thanks.

V hard to test motor EGT at full load as I live in Cloncurry and there are no hills like what would be required.

In terms of how deep my hit pockets are - just deep enough to splash out on a $500 pyroguage - not deep enough to blow a $10k motor. My triple carbed EH is my play car. This one is meant to be the reliable tourer!

If I am able to get EGT down by increasing boost slightly is this a win/win? That is, will I get better power and lower EGT? What are the negatives of this?

Why would someone had run the fuel at this level and not matched the boost?

I'll order a boost guage and go from there.

Thanks for the help.
Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests