Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
80 series double cardon
Moderators: toaddog, Elmo, DUDELUX
80 series double cardon
hi just thought id give rap to gibson engineering at edgeworth. did a doublecardon joint for me using my shaft for $450 bargain shoped around and found most were $600 plus . was a really nice bloke too not a smartass like some are(not all!).pm me for there number if required
driveshaft
I also can recommend there D/C shafts,just put one in my 100 series......
Fixed all the vibration problems...................
Fixed all the vibration problems...................
105 series, 35' MTR's, 5'' lift ToughDogs, Twin Locked, Angry Bars, Front Radius arm Flip & X-Thingy.........................
drive shaft
alchemist wrote:they don't last for long, I had one done cost me $400 from veem all up, real good price I thought... but now after about 10,000k's the vibration has come back and god knows why.....
fit a part time kit and this will fix your problom unless you do more than 80ks in 4WD which you probally wont do anyway Mark do a kit for about $590. or you can use a transfer out of a DX model.
current truck, 105 series GXL diesel 6" springs & twin pro lockers
sierra LWB spoa one wide track diffs twin locked
Sierra Parts Wanted pm me
sierra LWB spoa one wide track diffs twin locked
Sierra Parts Wanted pm me
hi mine was the front aswell. mine was also vibrating at about 40 k ph before the double cardon and i figure if i need it off road probly better to do it this way as once your off road and in 4wd (with a 2wd adapter) your still stressing the unis and sooner or later there gonna snap.wouldnt want to be in a precarious possition when this happens. alchemist check that the face of the end ofthe shaft is absolutely flush against the face of the transfer case mine had a little bit of build up between it and was doing the same thing so i took it off and cleaned the face and it was all good or maybe they didnt replace your unis for $400 and they might be stuffed.
hi again im pretty unfamiliar with the part time setup and i was just having a thought and im thinking does the part time setup actually move the mounting of the shaft downwards therefore reducing the angle on the unis or does it still maintain the same angle as standard. coz i thought it would still be a problem off road if it has too much angle and chew out unis thanks wayne
Wayne the angle of the dangle stays thesame....just that the front shaft doesnt move till your hubs are in.muddy80s wrote:hi again im pretty unfamiliar with the part time setup and i was just having a thought and im thinking does the part time setup actually move the mounting of the shaft downwards therefore reducing the angle on the unis or does it still maintain the same angle as standard. coz i thought it would still be a problem off road if it has too much angle and chew out unis thanks wayne
If you get a dx transfer, you can run a PTO winch off it...
Andrew
Re:
crankycruiser wrote:I put a double cardon in mine.. they never last long even with regular greasing.. ive had mine rebuilt a couple of times now..
Im over it now,. jsut gunna go part time
a grave dig i know, i just put a 4" kit in mine and have the suspected vibrations, i was looking at putting a double cardon joint in but as stated they never last, would a CV tail shaft be a more longer lasting option??
Ill look at doing a part time kit later on down the track.
Evan
www.energizedracing.com
Support from:
Locktup 4x4
Arb Newcastle
Genr8 LED lighting
Yukon Gear & Axle
Overkill Engineering
Ruffstuff Specialties
Support from:
Locktup 4x4
Arb Newcastle
Genr8 LED lighting
Yukon Gear & Axle
Overkill Engineering
Ruffstuff Specialties
Re: 80 series double cardon
Havn't tried this yet but check out the link for an alternative
http://www.outerlimits4x4.com/viewtopic ... 5#p1864595" onclick="window.open(this.href);return false;
http://www.outerlimits4x4.com/viewtopic ... 5#p1864595" onclick="window.open(this.href);return false;
1993 80 series, 4" tough dog adjustable bb lift kit, LPG, 35" MTR'S
brooksy wrote:Branden Tagg.....He is the King of all f@rkups & a Gimps bitch after hours
Re: Re:
I rekon just do the part time now, and put a double cardon on later. Won't cost you anymore, and will be the better setup. The double cardon will last alot longer when it's not being used on the road.evanstaniland wrote:crankycruiser wrote:I put a double cardon in mine.. they never last long even with regular greasing.. ive had mine rebuilt a couple of times now..
Im over it now,. jsut gunna go part time
a grave dig i know, i just put a 4" kit in mine and have the suspected vibrations, i was looking at putting a double cardon joint in but as stated they never last, would a CV tail shaft be a more longer lasting option??
Ill look at doing a part time kit later on down the track.
Evan
The worst part about being told you have Alzheimer's, is that it doesn't just happen once.
Re: 80 series double cardon
How do you get around the ABS as the sensors are on the front CV's? Or do you leave the standard hub flanges on instead of the free wheeling hubs?dow50r wrote:muddy80s wrote:hi again im pretty unfamiliar with the part time setup and i was just having a thought and im thinking does the part time setup actually move the mounting of the shaft downwards therefore reducing the angle on the unis or does it still maintain the same angle as standard. coz i thought it would still be a problem off road if it has too much angle and chew out unis thanks wayne
Wayne the angle of the dangle stays thesame....just that the front shaft doesnt move till your hubs are in.
If you get a dx transfer, you can run a PTO winch off it...
Andrew
Re: 80 series double cardon
Has anyone put the marks kit in? what is the difference between the Marks kit and the 4wd systems one?
what happens to the front ABS? does the light stay on the dash constantly?
Evan
what happens to the front ABS? does the light stay on the dash constantly?
Evan
www.energizedracing.com
Support from:
Locktup 4x4
Arb Newcastle
Genr8 LED lighting
Yukon Gear & Axle
Overkill Engineering
Ruffstuff Specialties
Support from:
Locktup 4x4
Arb Newcastle
Genr8 LED lighting
Yukon Gear & Axle
Overkill Engineering
Ruffstuff Specialties
Re: 80 series double cardon
If you fit free wheeling hubs the ABS will be disabled & the light will stay on until the hubs are locked. This will also make your vehicle illegal & may also result in insurance claim rejection.
Re: 80 series double cardon
Just go part time! All the frigging round i did with my DC i could of put 2 part time kits in u live and learn tho!
Cant comment on CVshafts tho
Cant comment on CVshafts tho
80 xtra cab
Supercharged LS1, Locked n shit
80 Wagon, TD Tourer, locked, Interco 35s, G turbo
Supercharged LS1, Locked n shit
80 Wagon, TD Tourer, locked, Interco 35s, G turbo
Re: 80 series double cardon
what problems did you have with your DC joints?
www.energizedracing.com
Support from:
Locktup 4x4
Arb Newcastle
Genr8 LED lighting
Yukon Gear & Axle
Overkill Engineering
Ruffstuff Specialties
Support from:
Locktup 4x4
Arb Newcastle
Genr8 LED lighting
Yukon Gear & Axle
Overkill Engineering
Ruffstuff Specialties
Re: 80 series double cardon
search Pirate4x4 for the tech pages on driveshafts and CV joints(Double Cardon).evanstaniland wrote:what problems did you have with your DC joints?
They wear quickly, dont increase the flex available in the drive shaft, can actually reduce it, and in a mostly std, but lifted 80series they will still be likely to vibrate to some extent. They are a bandaid solution.
RN wrote:pussy is out, its the log for me... Thank you Jesus.
Re: 80 series double cardon
Like 80_D said, they just didnt last, they are just a bandaid fix. Once i put the Cranky link in the front of mine it didnt have enuf angle either..evanstaniland wrote:what problems did you have with your DC joints?
Contratry to popular belief, u can get more angle out of a std CV than the Double cardon
80 xtra cab
Supercharged LS1, Locked n shit
80 Wagon, TD Tourer, locked, Interco 35s, G turbo
Supercharged LS1, Locked n shit
80 Wagon, TD Tourer, locked, Interco 35s, G turbo
Re: 80 series double cardon
is there any option that can be done without stuffing up the ABS? whats the point of buying a car with safety features to disable them?
also does anyone know the difference between the marks kit and the 4wd systems kit?
would these be worth the $1700?
http://hardyspicer.com.au/cornay_joint.asp" onclick="window.open(this.href);return false;
EVan
also does anyone know the difference between the marks kit and the 4wd systems kit?
would these be worth the $1700?
http://hardyspicer.com.au/cornay_joint.asp" onclick="window.open(this.href);return false;
EVan
www.energizedracing.com
Support from:
Locktup 4x4
Arb Newcastle
Genr8 LED lighting
Yukon Gear & Axle
Overkill Engineering
Ruffstuff Specialties
Support from:
Locktup 4x4
Arb Newcastle
Genr8 LED lighting
Yukon Gear & Axle
Overkill Engineering
Ruffstuff Specialties
Who is online
Users browsing this forum: No registered users and 9 guests