Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Bodylift tech
Moderator: Tiny
Bodylift tech
I can't get the back studs out at the the chasis. I tried to tighten two nuts onto the thread and and undo it but there isn't any room for a spanner. Has anyone got some suggestions, before I attack with an angle grinder?
Cheers
jimmy
Cheers
jimmy
89 Narrow CracK Feroza EL- X
2001 NM Pajero Exceed 3.5V6
Coming Soon 2010 Defender 90
2001 NM Pajero Exceed 3.5V6
Coming Soon 2010 Defender 90
#
CRC or WD40 and leave it over night
Andy...........
All post's are submitted with the assistance of alcohol
"OUR FEROZA" is Debt Propelled
All post's are submitted with the assistance of alcohol
"OUR FEROZA" is Debt Propelled
Jimmy,
how high are you going with the body lift? 50mm or 60mm? Did you buy fine metric thread, 10mm bolts for the front 2 and rear 2 blocks? Saves cutting or bashing off existing nuts...
Dave.
how high are you going with the body lift? 50mm or 60mm? Did you buy fine metric thread, 10mm bolts for the front 2 and rear 2 blocks? Saves cutting or bashing off existing nuts...
Dave.
1994 Feroza SX II 2 inch suspension lift, 2.5 inch body lift, 31 inch Pro Comp X-terains, extractors and sports exhaust.
www.geocities.com/davefogwill
www.geocities.com/davefogwill
Dave,
I got the high tensile metric thread nuts and bolts from a bearing and bolts specialist. I basically studied your procedure and some of the old threads on this forum to gain the knowledge to do the lift- you legend ! The lift will be 50mm I am happy with that as it is the maximum body lift allowed in Qld. One bolt to go
Cheers
Jimmy
I got the high tensile metric thread nuts and bolts from a bearing and bolts specialist. I basically studied your procedure and some of the old threads on this forum to gain the knowledge to do the lift- you legend ! The lift will be 50mm I am happy with that as it is the maximum body lift allowed in Qld. One bolt to go
Cheers
Jimmy
89 Narrow CracK Feroza EL- X
2001 NM Pajero Exceed 3.5V6
Coming Soon 2010 Defender 90
2001 NM Pajero Exceed 3.5V6
Coming Soon 2010 Defender 90
Jimmy L wrote:Dave,
I got the high tensile metric thread nuts and bolts from a bearing and bolts specialist. I basically studied your procedure and some of the old threads on this forum to gain the knowledge to do the lift- you legend ! The lift will be 50mm I am happy with that as it is the maximum body lift allowed in Qld. One bolt to go
Cheers
Jimmy
well stop writing on here until you finish. PICS.
I went to LCMP with this guy and that car. madman!!!!!!!
Heath & Melissa - 93 GQ LWB.
Heath, Im a madman eh? that's harsh if my memory serves me, you were the ringleader on that little trek and I was just a follower. Whose idea was it to go up that goat track anyway?
Well, completed the lift except for bullbar and rear bumper, and am pleased with it. Total cost of bolts,washers and blocks $140, a bit of time afterwork. That's heaps better than coffing up $700- $800 for something that is relatively simple to do.
Now I can put a set of 31in mud terrians on when I get the cash and it's ready to rock n roll. Plus my rear leaf springs are badly sagged due to carrying 4 grown men and large quantities of beer along the beach.
Thanks to Dave Fogwill and others for advise on doing a bodylift to a feroza, it was a good experience I think I know my vehicle better as a result. Does anyone want a cheap set of genuine Feroza rims and BFG A/t, going for cheap?
Cheers
Well, completed the lift except for bullbar and rear bumper, and am pleased with it. Total cost of bolts,washers and blocks $140, a bit of time afterwork. That's heaps better than coffing up $700- $800 for something that is relatively simple to do.
Now I can put a set of 31in mud terrians on when I get the cash and it's ready to rock n roll. Plus my rear leaf springs are badly sagged due to carrying 4 grown men and large quantities of beer along the beach.
Thanks to Dave Fogwill and others for advise on doing a bodylift to a feroza, it was a good experience I think I know my vehicle better as a result. Does anyone want a cheap set of genuine Feroza rims and BFG A/t, going for cheap?
Cheers
Last edited by Jimmy L on Tue Apr 13, 2004 7:43 am, edited 1 time in total.
89 Narrow CracK Feroza EL- X
2001 NM Pajero Exceed 3.5V6
Coming Soon 2010 Defender 90
2001 NM Pajero Exceed 3.5V6
Coming Soon 2010 Defender 90
Who is online
Users browsing this forum: No registered users and 20 guests