i have a 94 td42 n/a and i am putting on my new pump i have all the dial indicator gear just wandering what is a good plunger travel for advancing them a bit i know the spec is 0.74mm future plans are to turbo so can i set it up for the future or .... yeah any first hand experience would be helpful i work for cummins so nuthing is too hard on these little engines
Thanks For Youre Help , Mitch
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
pump timing td42
pump timing td42
1994 Nissan Patrol ST Ute TD42 N/A With Extra Goodies
Re: pump timing td42
bump. id be interested to know if anyone has any info, unless its secret information...
Re: pump timing td42
im also very interestedrumpig89 wrote:bump. id be interested to know if anyone has any info, unless its secret information...
85 hi top drover, 31s, 2 inch exended shackles 2 inch bl.
88 tb42 swb mav,35 claws, 4 inch lift
88 tb42 swb mav,35 claws, 4 inch lift
Re: pump timing td42
No doubt its still a secret 
Re: pump timing td42
Its no secret, .74mm @ tdc is the correct spec. You could go to .8 but it may be noisy. Fuel is what gives you the power.
Andy
Andy
www.diesel-tec.com.au Ph 03 9739 5031
Ball bearing turbo upgrades for factory turbo vehicles. Got a diesel question just ask.
Home of the twin turbo shorty and many 150rwkw+ patrols.
Ball bearing turbo upgrades for factory turbo vehicles. Got a diesel question just ask.
Home of the twin turbo shorty and many 150rwkw+ patrols.
Re: pump timing td42
how much advance? is 6' too much? I think standard is 3' but 6 lowered my egts and gave a good burn.
GQ with 30 PSI of TD42T.........
Re: pump timing td42
I put mine to .86 no worries boost n fuel and fuel goes well no probs
Ford Maverick ute, gen 3 boost,kewish auto, twin locked 17"kmc enduro bead lock rims, POW 84 winch wiring
Re: pump timing td42
can someone give me a quick run through? I have fully rebuilt my engine, and am about to fit a gu pump and id like to do it myself, so u set engine to tdc, fit pump tool, set to .74 and rotate engine to see how far it drops off tdc?
85 hi top drover, 31s, 2 inch exended shackles 2 inch bl.
88 tb42 swb mav,35 claws, 4 inch lift
88 tb42 swb mav,35 claws, 4 inch lift
Re: pump timing td42
The sepcs are for the turbo pumps .626mm for Factory Intercooled engines
.740mm for Non intercooled motors.
Another big factor when setting pump timing is what the injector pressure's are set at.
.740mm for Non intercooled motors.
Another big factor when setting pump timing is what the injector pressure's are set at.
Re: pump timing td42
I've got an 89 GQ TD42 that i fitted a GU TD42 turbo pump to. Set to .65mm and it goes an absolute treat.
Never done the injectors on it either. I'd set it to .7 or .74 and run it and see what you think. I'd be disinclined to advance it too much unless it's being done by a diesel professional.
Mine was checked by a diesel pro after i'd fitted the pump and done the timing, all he did was wind the fuel up a little more than i had it and check it over and said it was awesome, could've got more power out, but he reckoned it'd be at the cost of fuel and shorter engine life.
Never done the injectors on it either. I'd set it to .7 or .74 and run it and see what you think. I'd be disinclined to advance it too much unless it's being done by a diesel professional.
Mine was checked by a diesel pro after i'd fitted the pump and done the timing, all he did was wind the fuel up a little more than i had it and check it over and said it was awesome, could've got more power out, but he reckoned it'd be at the cost of fuel and shorter engine life.
Re: pump timing td42
Its interesting to read, he was a diesel professional. Did he just use the fuel screw? Or do a proper job on the compensator?suggy126 wrote:I've got an 89 GQ TD42 that i fitted a GU TD42 turbo pump to. Set to .65mm and it goes an absolute treat.
Never done the injectors on it either. I'd set it to .7 or .74 and run it and see what you think. I'd be disinclined to advance it too much unless it's being done by a diesel professional.
Mine was checked by a diesel pro after i'd fitted the pump and done the timing, all he did was wind the fuel up a little more than i had it and check it over and said it was awesome, could've got more power out, but he reckoned it'd be at the cost of fuel and shorter engine life.
Who is online
Users browsing this forum: No registered users and 1 guest