Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
rear wheel bearing 60 series
Moderators: toaddog, Elmo, DUDELUX
rear wheel bearing 60 series
Spent nearly the whole day today trying to replace the stupid bearings/seals cause it was leaking, pretty much everything that could go wrong has, except for once all the bearings where the correct ones, but now the bearing locknut just refuses to screw in far enough. The manual says to use a "special tool" to do it up, I've been using a hammer and now a hammer and screwdriver but its still not in anywhere near far enough in and I'm out of ideas on how to move it. The thread looked fine (its now dark and can't check) and I think the bearing is in far enough cause I tried tapping that in further without the locknut thing over it.
Does anyone know what this "special tool" is and where to get it? or any homemade alternatives.
Does anyone know what this "special tool" is and where to get it? or any homemade alternatives.
60 + Turbo, 33"s :armsup:
Re: rear wheel bearing 60 series
The special tool is just an adapter for a ratchet to turn the locking nut.
I haven't heard of your problem before, usually people find the lock nut doesn't go in far enough because they haven't punched the bearing races in far enough. You didn't forget the lock plate that goes behind the nut? Otherwise i'd double check the bearings are the same size as the ones that came out.
I haven't heard of your problem before, usually people find the lock nut doesn't go in far enough because they haven't punched the bearing races in far enough. You didn't forget the lock plate that goes behind the nut? Otherwise i'd double check the bearings are the same size as the ones that came out.
The worst part about being told you have Alzheimer's, is that it doesn't just happen once.
Re: rear wheel bearing 60 series
Actually what I said sounds like your problem. I was thinking the lock nut was running out of thread and the hub was still loose. Should've read your post better
The worst part about being told you have Alzheimer's, is that it doesn't just happen once.
Re: rear wheel bearing 60 series
Yeah i've got the lack plate in there, the bearings where the same, but one of them had different numbers, but both ID and OD where the same so didn't think anything of it thought it might just be different part numbers from different brands, but I didn't check the width against the old one! Will do that tomorrow.
60 + Turbo, 33"s :armsup:
Re: rear wheel bearing 60 series
"one of the bearings had a different number" ooh don't like the sound of that.
Re: rear wheel bearing 60 series
check the hub isn't fouling on some crap at the back the stub axle where the seal sits, had a similar problem before and i just gave eveything a good cleanup and a grease and it all went back together.
75 series cruiser. Turbo, 5in lift, 34's, rear locker and other goodies
Re: rear wheel bearing 60 series
In the daylight I can now see the outer bearing cup just isn't going in far enough in the housing, no matter how hard I hit it. Housing looks ok doesn't seem to be any gouges or scoring that should stop it. So I got the hub in the oven now and the cup in the freezer if it doesn't go in after this I'm gunna have to admit defeat and take it somewhere
60 + Turbo, 33"s :armsup:
Re: rear wheel bearing 60 series
The inner and outer bearings are different.........
The Silver Bullet - BJ74
Where the actions at Ontrack 4wd Club
http://www.ontrack4wdclub.com/
[url]http://www.cams.com.au/[/url]
Where the actions at Ontrack 4wd Club
http://www.ontrack4wdclub.com/
[url]http://www.cams.com.au/[/url]
Re: rear wheel bearing 60 series
hulsty wrote:The inner and outer bearings are different.........
lol
03 HDJ100R GXL / 94 FJ45-80
Re: rear wheel bearing 60 series
lol, ya think?hulsty wrote:The inner and outer bearings are different.........
Heating and cooling trick worked, only now my oven smells a bit like grease
60 + Turbo, 33"s :armsup:
Re: rear wheel bearing 60 series
New thread: how to explain this to the wifeRockyF75 wrote:lol, ya think?hulsty wrote:The inner and outer bearings are different.........
Heating and cooling trick worked, only now my oven smells a bit like grease
The worst part about being told you have Alzheimer's, is that it doesn't just happen once.
Re: rear wheel bearing 60 series
http://www.youtube.com/watch?v=5lmQE3_oiNQ" onclick="window.open(this.href);return false;
I found this really helpful, and some of you may also.
Daniel
I found this really helpful, and some of you may also.
Daniel
Who is online
Users browsing this forum: No registered users and 3 guests