Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

coil spring retention or drop out cones

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply

If you have a coil sprung rig do you run

retained top and bottom
5
24%
retained one end only and relocation device other end
10
48%
unretained both ends cause it doesnt need it
3
14%
the only coils in my rig are in the door detent latch
3
14%
 
Total votes: 21

Posts: 329
Joined: Thu Nov 07, 2002 5:24 pm
Location: Brisbane

coil spring retention or drop out cones

Post by derangedrover »

spring retention or drop outs, which works best?
Top
Posts: 1361
Joined: Thu Oct 24, 2002 8:47 pm
Location: Now in a happy place.

Post by Cheezy4x4 »

As the Mav had alot of travel in the rear I have tried just about everything.
When I retained both ends I was stuffing coils as it compresses and stretches the coils and I would go through rear coils every 3 months.
I also tried very long soft coils that retained themselves, but for the travel thay had to be too soft. So I ended up with retained on the bottom and a cone ( no TJ Pete) down the middle of the top. :D
NOW ABLE TOO SAY WHAT I WANT WITHOUT FEAR OF LOOSING SALES.
The person who says it cannot be done should not interrupt the person doing it.
Top
Posts: 119
Joined: Wed Oct 23, 2002 7:54 pm
Location: Brisbane, Australia

Contact:
Contact tjpete

Post by tjpete »

Cheezy4x4 wrote:As the Mav had alot of travel in the rear I have tried just about everything.
When I retained both ends I was stuffing coils as it compresses and stretches the coils and I would go through rear coils every 3 months.
I also tried very long soft coils that retained themselves, but for the travel thay had to be too soft. So I ended up with retained on the bottom and a cone ( no TJ Pete) down the middle of the top. :D


On the Planet K O N E they run tapered wire, progressive coils which eliminates this problem.
Peter Kincade
Top
Posts: 374
Joined: Mon Oct 28, 2002 8:09 pm
Location: BRISBANE

Post by v8grunt »

BACK TO THE FUTURE " leaf springs "
Top
Posts: 119
Joined: Wed Oct 23, 2002 7:54 pm
Location: Brisbane, Australia

Contact:
Contact tjpete

Post by tjpete »

v8grunt wrote:BACK TO THE FUTURE " leaf springs "


Glen is on the mark here. Look at the number of USA championship vehicles that still run leaf packs. Yes, you do have wrap issues but you don't have control arm issues. And leaf technology still continues to evolve. Look at Overkill's!
Peter Kincade
Top
Posts: 691
Joined: Thu Dec 26, 2002 11:21 pm
Location: Lebanon

Contact:
Contact DiscoDino

Post by DiscoDino »

Bottom retained, top coned, that is what I have on the rear of the Disco, and I can get ~550 on a 30 degree ramp. Going for something more radical to stretch it to 750 soon...
Coned in the rear is the way to go!
front, not sure yet???
LR Disco truggy:
42" Iroks, ZF, dual cases & ARBs, 30 splined, Longfielded, OMEs, Optimas, M8274-50s, Rockstomper rope & Bead-L
LR D-90 TD5 ST:
33" BFT AT, tuned, caged, 1/2 top
Top
Posts: 374
Joined: Mon Oct 28, 2002 8:09 pm
Location: BRISBANE

Post by v8grunt »

POS has leaf front and coil on the rear, at xrcc r1 the car appeared to be very stable with loads of travel all round, but i failed to look at his coil drop set up.

come on POS what have you done to the rear.

glen
Top
Posts: 1813
Joined: Sun Oct 20, 2002 3:31 pm

Post by Strange Rover »

I got mine retained top and bottom all around and IMO is the best setup for my rig.

POS has his retained top and bottom in the rear.

Sam
Top
Posts: 2388
Joined: Sun Nov 24, 2002 10:20 pm
Location: bacabugari

Contact:
Contact big red

Post by big red »

i got sick of bending strap mounts and breaking straps so i retained the bottom and coned the top.that was for the rear...
the shocks and bindup limit the front so nothing done there.
it does 1000mm front and 1125mm rear .
on a 30 degree ramp it goes up 2010 front and 2250 rear.
shock and spring mounts are all factory except for the front radius arm drop brackets and still uses original bump stops.
everything is bolt on so i can go back to standard when i get caught.
[url=http://bigred.redbubble.com/][color=red][b]You can follow me but its gunna hurt ![/b][/color][/url]
event pics http://bigred.redbubble.com/
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 111 guests