I am looking for a better drive belt set-up for my 3f Toyota motor as the hydro steering pump is to hard on the stock vee belt. When the pump gets loaded up the belt slipping sometimes even with heaps of tension on it and its chewing through belts. Has or can anyone shed some light on to different belt options that can be used and how to adapt them to my motor?
Thanks Nathan
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Drive belts?
Moderators: toaddog, TWISTY, V8Patrol, Moderators
Drive belts?
TEAM TONKA
SPONSORED BY
HANCOCK SHEETMETAL
Locktup4x4.com.au
FOR ALL HARDCORE OFFROAD GEAR
SPONSORED BY
HANCOCK SHEETMETAL
Locktup4x4.com.au
FOR ALL HARDCORE OFFROAD GEAR
Posts: 3725
Joined: Wed Jun 30, 2004 1:45 pm
Joined: Wed Jun 30, 2004 1:45 pm
Location: Blue Mountains, or on a rig somewhere in bumf*ck idaho
Re: Drive belts?
Can you adapt a toothed cam timing belt and pulley off a cam timing set?
http://www.populationparty.org.au/
Posts: 3725
Joined: Wed Jun 30, 2004 1:45 pm
Joined: Wed Jun 30, 2004 1:45 pm
Location: Blue Mountains, or on a rig somewhere in bumf*ck idaho
Re: Drive belts?
Just a few things.......
Is it the stock pump? If not, what pump is it and what is the size of the pully compared to stock
Is it in the stock position and is the belt in the stock configuration?
What is the percentage of the pully's diameter or angular portion that is contacted by the belt?
Is it possible to fit an idler to get more belt contact percentage? You may find that by doing this you increase the HP you can push throught the belt before it slips as there's a higher contact patch.
A lot of the guys running LS motors and hi performance pumps are using serpentine ribbed belts instead of vee belts. Does the pully system on the 3F lend itself to swapping out the vee pullys for ribbed pulleys?
Is it the stock pump? If not, what pump is it and what is the size of the pully compared to stock
Is it in the stock position and is the belt in the stock configuration?
What is the percentage of the pully's diameter or angular portion that is contacted by the belt?
Is it possible to fit an idler to get more belt contact percentage? You may find that by doing this you increase the HP you can push throught the belt before it slips as there's a higher contact patch.
A lot of the guys running LS motors and hi performance pumps are using serpentine ribbed belts instead of vee belts. Does the pully system on the 3F lend itself to swapping out the vee pullys for ribbed pulleys?
http://www.populationparty.org.au/
Re: Drive belts?
Its I psc SP-1200X pump with a pulley that's the same size as the stock one and its now mounted where the air con was and where using what was the air con tensioner on it with the belt running the same as the air con did. There is 45% of the pulley contacted by the belt. Currently the v tensioner is pulling upwards witch intuit pulls the belt away a little from the pulley but I think I may be able to swap to a flat tensioner to push down increasing the contact to maybe 60%. I was hoping that there would be a way to swap to a better ribbed belt system all together rather then keep struggling with the one i have but can not find any info on some thing to suit the 3F.rockcrawler31 wrote:Just a few things.......
Is it the stock pump? If not, what pump is it and what is the size of the pully compared to stock
Is it in the stock position and is the belt in the stock configuration?
What is the percentage of the pully's diameter or angular portion that is contacted by the belt?
Is it possible to fit an idler to get more belt contact percentage? You may find that by doing this you increase the HP you can push throught the belt before it slips as there's a higher contact patch.
A lot of the guys running LS motors and hi performance pumps are using serpentine ribbed belts instead of vee belts. Does the pully system on the 3F lend itself to swapping out the vee pullys for ribbed pulleys?
TEAM TONKA
SPONSORED BY
HANCOCK SHEETMETAL
Locktup4x4.com.au
FOR ALL HARDCORE OFFROAD GEAR
SPONSORED BY
HANCOCK SHEETMETAL
Locktup4x4.com.au
FOR ALL HARDCORE OFFROAD GEAR
Re: Drive belts?
can you go to a dual belt setup ?
The excessive tension will not be doing any favours to the bearings\bush's in the system
The excessive tension will not be doing any favours to the bearings\bush's in the system
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
Who is online
Users browsing this forum: No registered users and 114 guests