Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
patroless
patroless
i want my truck back
ive been patroless for 9 days now...... its starting to get to me!
hopefully it will be finished tomorrow arvo
Roly
ive been patroless for 9 days now...... its starting to get to me!
hopefully it will be finished tomorrow arvo
Roly
08 340kw HSV Maloo 6.2L
John Roly
Melbourne Again
John Roly
Melbourne Again
Got a call from macquarie. Noisey Transfer gears in low range when backed off throttle is worn input and output bearings. Too much endfloat allowing gears to slightly touch.
They said they havent had a GU2 opened up that has done as many thousand kms in 4wd that mine has.
Oil has been clean and changed more than recommended by nissan
Nissan want $600 for the 2 bearings.. Ouch...
They are sourcing the bearings directly from SKF or Nachi (Sp) themselves...
Roly
They said they havent had a GU2 opened up that has done as many thousand kms in 4wd that mine has.
Oil has been clean and changed more than recommended by nissan
Nissan want $600 for the 2 bearings.. Ouch...
They are sourcing the bearings directly from SKF or Nachi (Sp) themselves...
Roly
08 340kw HSV Maloo 6.2L
John Roly
Melbourne Again
John Roly
Melbourne Again
The bearings will probably be half the price going direct, I had a inner front wheel bearing crap itself this arvo. Last time I stupidly went to Repco, they had to order them in and they cost me something like $100 for the 2 wheel bearings, the oil seal and the needle bearing that holds the axle stub right next to the CV. This time I went to Bearing Wholesalers, and got all of the same bits for $66 and they had them on the shelf, and the car is now fixed and rolling again. Lesson learned by me.
[size=100][url=http://www.vickrawlers.com/]VicKrawlers.com[/url]
[url=http://www.drfwdc.org.au/]Dandenong Ranges 4wd Club[/url][/size]
[url=http://www.drfwdc.org.au/]Dandenong Ranges 4wd Club[/url][/size]
bogged wrote:MKPatrolGuy wrote:The bearings will probably be half the price going direct, I had a inner front wheel bearing crap itself this arvo.
is that heap still crumbling..... wait for the Chev if you think its crumbling now!!!!!!
lol, i can't wait. It was actually in much better than the one I replaced last time. Only took me an hour and a half, and no grinder needed 8) It was my fault, I should have replaced it when i did the other side to be sure. But I had things to do that were more fun
[size=100][url=http://www.vickrawlers.com/]VicKrawlers.com[/url]
[url=http://www.drfwdc.org.au/]Dandenong Ranges 4wd Club[/url][/size]
[url=http://www.drfwdc.org.au/]Dandenong Ranges 4wd Club[/url][/size]
roly wrote:still waiting
t case kit didnt arriv till 4pm
looks like next week now.
now i know why i only get my truck wored on when i go overseas........
over 2 weeks is gonna kill me
roly
Gotta hate the withdrawl symptoms
[size=100][url=http://www.vickrawlers.com/]VicKrawlers.com[/url]
[url=http://www.drfwdc.org.au/]Dandenong Ranges 4wd Club[/url][/size]
[url=http://www.drfwdc.org.au/]Dandenong Ranges 4wd Club[/url][/size]
bogged wrote:DirtPigs wrote: are enjoying our long weekends out in the scrub
More like Ash by the end of the weekend
Well we were fortunate enough to enjoy a day up at the Watagans today. Good to report that there were no recently burnt out areas, but it does look as if the fires have been thru on the last 6 months in places...
I did manage to push the drivers side sill in a little in a decent sized rut... first carnage to the GQ... damn I need a lift and protection.
LOL... I know, I'm just so keen to get out an drive that i can't wait for all the mods to be done... I'm having a ball anyway and sure do have a better appreciation for what a stock GQ can do. Pretty damn impressive.
The Bridgestone ATs aren't too shabby a tyre either...
I hope to be getting the lift and protection in the next month or so.
The Bridgestone ATs aren't too shabby a tyre either...
I hope to be getting the lift and protection in the next month or so.
Who is online
Users browsing this forum: No registered users and 37 guests