Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

GU 4"lift ?

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Forum rules
Post Reply
Posts: 12
Joined: Sat May 01, 2004 2:15 pm
Location: South Eastern Melbourne

GU 4"lift ?

Post by gdcobb »

I am looking at doing a 4" suspension lift on my GU Wagon
on the Cheap (Not New Prices)
Does anyone have the stuff i need!

Springs
Shocks
Panhard Rods?
Caster plates?

"What about Nutters wanting to go taller"I'll buy your 4" Stuff
Last edited by gdcobb on Wed May 19, 2004 9:22 am, edited 1 time in total.
Top
Posts: 59
Joined: Thu May 06, 2004 4:38 pm
Location: Melbourne

Longer and Stronger

Post by GQboy »

I rekon you should give Shanny Enginering a buzz , he is down in sale I rekon he is pretty clued on to that sort of stuff. After that you will be able to fit creepy crawleys under it no worries......
There are two infinates in life , The universe and Patrols!
Top
Posts: 2388
Joined: Sun Nov 24, 2002 10:20 pm
Location: bacabugari

Contact:
Contact big red

Post by big red »

6 to 10 mm
fit the coils then measure the panhard length.
you can drive it ok with standard length panhards if you wanna be extra cheap :D
[url=http://bigred.redbubble.com/][color=red][b]You can follow me but its gunna hurt ![/b][/color][/url]
event pics http://bigred.redbubble.com/
Top
Posts: 12
Joined: Sat May 01, 2004 2:15 pm
Location: South Eastern Melbourne

Re: Longer and Stronger

Post by gdcobb »

GQboy wrote:I rekon you should give Shanny Enginering a buzz , he is down in sale I rekon he is pretty clued on to that sort of stuff. After that you will be able to fit creepy crawleys under it no worries......


THE CREEPY CRAWLYS ALREADY FIT, BUT WHAT I REALLY WANT WONT FIT!!!!!
Top
Posts: 12
Joined: Sat May 01, 2004 2:15 pm
Location: South Eastern Melbourne

Re: GU 4"lift ?

Post by gdcobb »

gdcobb wrote:I am considering fitting 4" coils to my GU, my shocks are long enough
i already have 3 deg caster bushes and extended brake lines.i am to Tight assed to buy Adjustable Panhard Rods so i am wondering i anone can tell me how much longer my standard ones need to be for a 4" lift.
I have the farcilaties were i work to have them lenghtend a strenghtend

Any advice whould be great
Top
Posts: 2820
Joined: Sun May 25, 2003 10:04 am
Location: Redbank Plains, QLD

Post by Daisy »

There isnt an actual measurement as EVERY vehicle VARIES :roll:

Spring rates - different etc etc.

Now.. try this...

Install your 4 inch lift. and leave the stock panhard in place whilst installing..

THEN once installed.. remove one of the panhard bolts and remove that end..

ROCK the car a bit to make sure that the springs have settled.

Measure the amount you need to extend your panhard.

Cut and lengthen the panhard.

REFIT.

Pretty simple?? unless you're lookin into harder options :roll:

The vehicle SHOULD be drivable on standard panhard = tyre will stick out an inch to drivers side. Shouldnt be a problem if you're already lifted - no rubbing to take vehicle to and from workshop if you're planning on that.

Cheers and good luck

TOM
Top
Posts: 45681
Joined: Wed Nov 27, 2002 10:13 am

Re: Longer and Stronger

Post by bogged »

gdcobb wrote:THE CREEPY CRAWLYS ALREADY FIT, BUT WHAT I REALLY WANT WONT FIT!!!!!



SO WHAT DO YOU REALLY WANT TO FIT?




Just wondering why he was yellin'
Top
Posts: 12
Joined: Sat May 01, 2004 2:15 pm
Location: South Eastern Melbourne

Re: Longer and Stronger

Post by gdcobb »

bogged wrote:
gdcobb wrote:THE CREEPY CRAWLYS ALREADY FIT, BUT WHAT I REALLY WANT WONT FIT!!!!!



SO WHAT DO YOU REALLY WANT TO FIT?


36-37s

Just wondering why he was yellin'
Top
Posts: 56
Joined: Mon May 17, 2004 8:44 pm

Post by sideways »

yes i might have some shocker and some springs soon say in 2 weeks
Top
Posts: 677
Joined: Mon Nov 18, 2002 10:00 am
Location: Melbourne

Contact:
Contact roly

Post by roly »

my 4-5" springs (dobinsons) are sitting in a box in melbourne after i took them out

$200 with the ext'd bumpstops for the front


can do a deal on my shocks as i will be taking them off shortly (OME - L series 4 months old)


also have adj. rear panhard to come off, just looking for a std one 1st
08 340kw HSV Maloo 6.2L
John Roly
Melbourne Again
Top
Posts: 12
Joined: Sat May 01, 2004 2:15 pm
Location: South Eastern Melbourne

SUSPENSION

Post by gdcobb »

sideways wrote:yes i might have some shocker and some springs soon say in 2 weeks
Thanks for the reply for my request
lit me know what you want for your gear $$$$ when you are ready!
Top
Posts: 2979
Joined: Mon Feb 24, 2003 7:03 pm
Location: Melbourne

Post by robbie »

roly, check pm ;)
Top
Posts: 601
Joined: Mon May 24, 2004 9:50 am
Location: south eastern melbourne

Re: Longer and Stronger

Post by GUEEY »

GQboy wrote:I rekon you should give Shanny Enginering a buzz , he is down in sale I rekon he is pretty clued on to that sort of stuff. After that you will be able to fit creepy crawleys under it no worries......
O.K GOOD THINKING
Top
Post Reply

Return to “Nissan”

Who is online

Users browsing this forum: No registered users and 7 guests