Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

some pics of my junk

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 295
Joined: Thu Jan 16, 2003 8:05 pm
Location: Brisbane, Southside

Post by Punchy »

sorry...just incase i missed it...what are these rockwell diff axles out of again ?
45 series ute - 308 -gas -35's- lifted -no flex..But i got air lockers !

2006 VX v8 4.7 Landcruiser, bog stock. It's black so its cool !
Top
Posts: 119
Joined: Wed Oct 23, 2002 7:54 pm
Location: Brisbane, Australia

Contact:
Contact tjpete

Post by tjpete »

mickbj42 wrote:i am in the process of clearancing the housing at the moment

here is what i cut off


Very nice work Mick.
Peter Kincade
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

Punchy wrote:sorry...just incase i missed it...what are these rockwell diff axles out of again ?


they are out of american military trucks like this
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

RUFF wrote:How much more lift do you think you will need to run to clear the centre?
And are you going to run a pinion brake or wheel brakes?


I got the measurements for you.

From centreline of axle to the top of the diff it is approx 280mm
For a comparison my cruiser diff is approx 140mm
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

about half way on the housing.

some pics
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

another
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

another
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

another
Top
User avatar
POS
Posts: 4318
Joined: Tue Oct 22, 2002 8:52 pm
Location: Perth

Post by POS »

Looks good :D
Top
Posts: 295
Joined: Thu Jan 16, 2003 8:05 pm
Location: Brisbane, Southside

Post by Punchy »

one word..

Holycrapbatman !
45 series ute - 308 -gas -35's- lifted -no flex..But i got air lockers !

2006 VX v8 4.7 Landcruiser, bog stock. It's black so its cool !
Top
Posts: 11892
Joined: Tue Oct 22, 2002 9:53 am
Location: Melbourne

Contact:
Contact N*A*M

Post by N*A*M »

Nice work with the high clearance cover. It'd probably be stronger than the old hemisphere too! Post pics of your disk brake conversion cos I might be able to learn from that. Pinion brakes suck. Have you weighed the Rockwells yet?
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

i havent weighed them.

I had two of them in the back of my liteace :shock: I think it bent it a bit cause the side door doesnt open as good as it used to. :lol:
Top
Posts: 15549
Joined: Tue Oct 22, 2002 9:23 am
Location: Your Mummas House!

Contact:
Contact bj on roids

Post by bj on roids »

that is the biggest bootiefabbed POS

im pretty jealous though, nice high clearance cover!!

i like this one better...but downunder bootiefab will never be teh same:
hands and mums dont count!!!
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

i dont have anything at home to roll the steel like. It will be ok how i have done it.
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

ok a bit of a trial fit of the cage/body today

got a couple of pics
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

another

The body looks like it is sitting alot higher than standard but it is only about 1/2 to 1 inch higher.

I have cut over 6 inches out of the side of the body so it looks like it is higher than it actually is.
Top
Posts: 11892
Joined: Tue Oct 22, 2002 9:53 am
Location: Melbourne

Contact:
Contact N*A*M

Post by N*A*M »

hurry up so i can see you drive down your backyard cliff with the rockwells
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

did a bit more today.

half made the rear portion of the chassis.

pics
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

another
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

and another
Top
Posts: 15549
Joined: Tue Oct 22, 2002 9:23 am
Location: Your Mummas House!

Contact:
Contact bj on roids

Post by bj on roids »

you ought to link this thread to pirate and ask them what they reckon!
hands and mums dont count!!!
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

you can do it.

i would be intersted to see what they think
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

i did a bit more on the rear of the chassis tonight

some pics
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

i still have to add a diagonal brace in between the upper and lower hoops

another pic
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

and dont worry i know the two side uprights towards the back arent square, i havent welded them in yet. I was just making a few measurements! :finger:
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

and one more.
Top
Posts: 11892
Joined: Tue Oct 22, 2002 9:53 am
Location: Melbourne

Contact:
Contact N*A*M

Post by N*A*M »

that's coming along swimmingly except it's ugly! where are the stylish curves man? it's gotta form over function don't you know?
Top
Posts: 16934
Joined: Sun Oct 20, 2002 6:57 pm

Post by RUFF »

You are getting better with your pics Mick. I see a Rockwell under the front there so where are the close ups of that :lol:
Top
Posts: 878
Joined: Tue Oct 22, 2002 9:53 am

Post by M&M Custom Engineerin »

i deliberately didnt crop that one. You just have to wait until i get to them. :lol:
Top
Posts: 295
Joined: Thu Jan 16, 2003 8:05 pm
Location: Brisbane, Southside

Post by Punchy »

i gets the sneaky feeling this is gonna be a tuff truck...
45 series ute - 308 -gas -35's- lifted -no flex..But i got air lockers !

2006 VX v8 4.7 Landcruiser, bog stock. It's black so its cool !
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 100 guests