Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
need front lockers
Moderator: Tiny
Here's another LSD type option that might be able to be adapted to suit:
www.phantomgrip.com
(and no, it's not as link to a porn site!
)
www.phantomgrip.com
(and no, it's not as link to a porn site!
)David
Good Luck finding a mini-spool that will fit !! If they don't make Lockers then there is no chance they will do a Spool or mini-spool off the shelf.
By Welding up the Diff Centre you are making a Mini-Spool.
Go to a Diff Specialist - DON'T try & weld it without dis-assembling the Diff if you want to do it properly. The ones that just pull off the front cover & splatter a bit of weld between the side / spider gears are the same people who have a bit of weld break off which then usually takes a nice little trip thru your R&P gears before settling in the bottom of the diff - along with a few of the teeth off your ring gear
The Diff Specialist will uninstall the Diff Centre & remove the Side Gears. These are then ground down to create a flat edge on each side. A solid piece of steel plate is then cut to fit between the flats on the Side Gears - & the whole lot is welded solid as one piece. If done properly there is nothing dodgy about it
Just as strong as a mini-spool - less moving parts than a standard diff - & completely locked
What more could you ask for ?
Just get it welded & be done with it......
Mike H.
By Welding up the Diff Centre you are making a Mini-Spool.
Go to a Diff Specialist - DON'T try & weld it without dis-assembling the Diff if you want to do it properly. The ones that just pull off the front cover & splatter a bit of weld between the side / spider gears are the same people who have a bit of weld break off which then usually takes a nice little trip thru your R&P gears before settling in the bottom of the diff - along with a few of the teeth off your ring gear
The Diff Specialist will uninstall the Diff Centre & remove the Side Gears. These are then ground down to create a flat edge on each side. A solid piece of steel plate is then cut to fit between the flats on the Side Gears - & the whole lot is welded solid as one piece. If done properly there is nothing dodgy about it
Just as strong as a mini-spool - less moving parts than a standard diff - & completely locked
What more could you ask for ?
Just get it welded & be done with it......
Mike H.
Mike Hennessy
Hilux Surf ( Big One )
Hilux Mountaineer ( Little one ) ;-)
Hilux Surf ( Big One )
Hilux Mountaineer ( Little one ) ;-)
Ok
Firstly, Murcod that manual is big, huge,massive even!
Secondly, Your right there are no mini spools availiable, it was only a long shot.
Thirdly, Looks like welding is the way to go. I was aware that you have to actually take the diff centre out. I had a mate that did one with the diff centre still in the car and earthed it through the diff body. His diff bearings were part of the circuit and there was a little bit of "weld" on each ball within the race. lets just say the diff didn't last too long. I was thinking bout ripping it out and welding pegs between the gears. Would that work.
Ah i'll just add it to the list of things that need doing!
Dave
Firstly, Murcod that manual is big, huge,massive even!
Secondly, Your right there are no mini spools availiable, it was only a long shot.
Thirdly, Looks like welding is the way to go. I was aware that you have to actually take the diff centre out. I had a mate that did one with the diff centre still in the car and earthed it through the diff body. His diff bearings were part of the circuit and there was a little bit of "weld" on each ball within the race. lets just say the diff didn't last too long. I was thinking bout ripping it out and welding pegs between the gears. Would that work.
Ah i'll just add it to the list of things that need doing!
Dave
Who is online
Users browsing this forum: No registered users and 0 guests