Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Removal of rear window

Tech Talk for Suzuki owners.

Moderators: lay80n, sierrajim

Forum rules
Post Reply
Posts: 56
Joined: Sun Nov 02, 2003 10:55 pm
Location: Adelaide South Australia

Removal of rear window

Post by dark matter »

I need to remove my rear window from my hard top. I have had to replace my rear door and my new one is a lovely red, but the rest of the car is grey.

Any ideas on how to remove it so I can spray the door, without cutting the rubber?

Thanks
96 GQ Patrol, TD42, snokel, 2" OME suspension
Top
Posts: 2817
Joined: Fri Feb 21, 2003 10:10 pm
Location: Hellbourne again

Post by bigsteve »

Just use a really small screwdriver to pry the rubber seal out, if its anything like the front screen it will be really easy, unless someone has used silicone or something to seal it.
yeshemesh
Top
Posts: 13555
Joined: Fri Nov 15, 2002 1:28 pm
Location: Melbourne

Post by grimbo »

Less hassle to just tape up the window and paint the door. Getting it out and back in without potentially damaging the glass or rubber might be a problem.
Ransom note = demand + collage
Top
Posts: 2817
Joined: Fri Feb 21, 2003 10:10 pm
Location: Hellbourne again

Post by bigsteve »

grimbo wrote:Less hassle to just tape up the window and paint the door. Getting it out and back in without potentially damaging the glass or rubber might be a problem.


I have done 3 for 3 without problems, it aint that hard if your careful
yeshemesh
Top
Posts: 1569
Joined: Tue May 11, 2004 9:43 pm
Location: Newcastle

Contact:
Contact HRZOOK

Post by HRZOOK »

Throw a brick through the back window ....Tim could help ya out here he is a brickie


Window out .....rubber intact.... :lol:


HRZOOK
Top
Posts: 293
Joined: Wed Oct 23, 2002 9:10 am

Post by skippy »

bigsteve wrote:
grimbo wrote:Less hassle to just tape up the window and paint the door. Getting it out and back in without potentially damaging the glass or rubber might be a problem.


I have done 3 for 3 without problems, it aint that hard if your careful



getting it out....it will only go one way. more likely roll and push the rubber seal from the inside to the outside. It'll eventually come out as you work arond the window.


getting it in...get some thin string ($2 clothes line rope from coles) and loop it through the groove in the rubber seal.....get some soapy water and lube up the rubber seal....place the window against and simply pull the rubber seal through using the string, starting at one side and work around the window until you have come full circle (so to speak).
Skippy


--------------------------------------------------
for all things digital, come to NEWflavour
'a better tasting multimedia experience'

http://www.newflavour.com/
--------------------------------------------------
Top
Posts: 215
Joined: Sun Jul 18, 2004 2:34 pm
Location: Tassie, Australia

Contact:
Contact 85zook

Post by 85zook »

tape it. mine came up fine!
Top
Posts: 56
Joined: Sun Nov 02, 2003 10:55 pm
Location: Adelaide South Australia

Post by dark matter »

Taping sounds good. Was going to try this weekend, too much rain. Will give it a go next weekend.

Thanks
96 GQ Patrol, TD42, snokel, 2" OME suspension
Top
Posts: 215
Joined: Sun Jul 18, 2004 2:34 pm
Location: Tassie, Australia

Contact:
Contact 85zook

Post by 85zook »

when you are taping it make sure you allow an extra ml around the edge of the rubber and tuck it in behind it slightly so the rubber is completely covered.
Top
Post Reply

Return to “Suzuki”

Who is online

Users browsing this forum: No registered users and 17 guests