Since picking up my Fez from getting it's lift done, it's developed a noise when travelling at over 100km. It's not there when i'm accelerating but as soon as i back off it starts a whining noise. I cant determine where it comes from but it seems to be round the front somewhere.
It's a long shot but I wanted to see if anyone else had a similar problem?
Could it be because of the increased air space between the tires and the guards?
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Noisey Car After Lift
Moderator: Tiny
?
Is it a problem if the driveshaft is misaligned? (other than the noise)
Posts: 3523
Joined: Sun May 18, 2003 8:42 pm
Joined: Sun May 18, 2003 8:42 pm
Location: Somewhere they can't reach me, shoot me or electrocute me...
Not really major in the short term, the vibration from the shaft comes from the two flanges (transfer case and diff) not being parallel, this can sometimes arise with short wheel base rigs when a lift is fitted. The pinion on the transfer case remains fixed, but the angle of the uni at the t case end increases to the lower diff position. The diff itself is lowered, but pivots from the link mounting point (the leaf spring chassis mount at the front of the spring) so the uni angle prolly won't increase that much at the diff pinion. The potential damage is from slight to bad-> uni joints get worn prematurely (pretty easy to change and about 35 bucks a throw) to flogged diff and t case bearings and housings.
You can buy wedge shims to correct bad pinion alignment, these fit between the diff and the leaf springs.
As you accelerate the diff pinion will tilt up to 'point' to the transfer case, on decel (with engine braking) the pinion will tilt down towards the ground, the axle wrap might be be exacerbating the vibration.
You can buy wedge shims to correct bad pinion alignment, these fit between the diff and the leaf springs.
As you accelerate the diff pinion will tilt up to 'point' to the transfer case, on decel (with engine braking) the pinion will tilt down towards the ground, the axle wrap might be be exacerbating the vibration.
Built, not bought.
What material did u use for the lift? Did you reuse the original factory body mounts as well? If you didnt, and the lift blocks are solid, then it could just be normal road noise, normally reduced and not heard because of the dampening and insulating effect of the rubber mounts, but now being transmitted into the body, which would now, in effect, be a huge sound box, like a guitar body.
Mud makes excellent toothpaste.
My driveline shakes have gone almost completely, only a mild rattle in second. I was also getting a grinding like noise coming when I hit the anchors and sometimes coasting, but fixed it.
I pulled the front hubs off and found most of the bearing grease had either washed out of gummed up with mud so I repacked them and now no noise and smooooth running!
I pulled the front hubs off and found most of the bearing grease had either washed out of gummed up with mud so I repacked them and now no noise and smooooth running!
On boooooost!!
?
Just thought i'd bring up an old post.
After new tyres and getting the bars wound up alittle more the noise has been greatly reduced. It's still there but it seems to be getting better.
Guess u were right croz......
After new tyres and getting the bars wound up alittle more the noise has been greatly reduced. It's still there but it seems to be getting better.
Guess u were right croz......
My noises are back... just about to go out to the shed to replace the wheel bearings.
I got a wheel alignment done much to the horror of the guy at pedders!! Apparently need new lower ball joints, outer tie rods and idler and pitman arms...
Looks like I'll be doing some more work on it pretty soon....
I got a wheel alignment done much to the horror of the guy at pedders!! Apparently need new lower ball joints, outer tie rods and idler and pitman arms...
Looks like I'll be doing some more work on it pretty soon....
On boooooost!!
?
why dont u just rebuild the whole front end........
sorry to hear that. just when u thought it was almost fixed.
sorry to hear that. just when u thought it was almost fixed.
Who is online
Users browsing this forum: No registered users and 0 guests