This one is in a RB25 turbo me and a mate have spent all lafternoon with no luck... Things ya do for mates
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Spiggot bearings
Spiggot bearings
Anyone out there have a easy way to get these dam f%$king things out.
This one is in a RB25 turbo me and a mate have spent all lafternoon with no luck... Things ya do for mates
This one is in a RB25 turbo me and a mate have spent all lafternoon with no luck... Things ya do for mates
Pump a heap of grease in behind it then get a bolt or something just the right size to fit in the centre and tap it in. The grease will push the spigot bearing out. You might need to pump a bit more grease in as the bearing moves out. The bolt you use will need to be just small enough not to catch on the bearing while still holding as much grease as possible in.
madness
nischev wrote:Pump a heap of grease in behind it then get a bolt or something just the right size to fit in the centre and tap it in. The grease will push the spigot bearing out. You might need to pump a bit more grease in as the bearing moves out. The bolt you use will need to be just small enough not to catch on the bearing while still holding as much grease as possible in.
Would you beleive we tried that with no luck
What was happening when you were trying it? Was the grease coming out past the bolt or was the bolt just going straight in? If the bolt was going straight in you need some more grease if it just wont budge be persistant and hit it with a bigger hammer they can be a real pita to get out.
Good luck.
Good luck.
madness
you can buy a device, it has a sharp tapered thread, and a grease nipple, same principle as above, screws into the bearing and uses a grease gun - hydraulic pressure to push out the spigot. Or you can get an internal puller that has a slide hammer type arrangement on it to drift it out??
There are no stupid questions, but there are a LOT of inquisitive idiots
Posts: 3523
Joined: Sun May 18, 2003 8:42 pm
Joined: Sun May 18, 2003 8:42 pm
Location: Somewhere they can't reach me, shoot me or electrocute me...
Shame the grease didn't work, it's a really good method.
Get a piece of M6 threaded rod (or 1/4 bsw) put a nut on the end of it, chuck on a steel body block (or a slide hammer head) and put a heavy washer and nut on the other end, insert the nut into the hole in the bearing, wedge it there so it cant fall out. Heat the crank just a little around the bearing (use an ordinary propane or butane burner) oxy will do but don't go crazy, this will release any loctite that may have been inserted with the bearing, and also open up the spigot recess in the crank, then get funky with the slide hammer.
Get a piece of M6 threaded rod (or 1/4 bsw) put a nut on the end of it, chuck on a steel body block (or a slide hammer head) and put a heavy washer and nut on the other end, insert the nut into the hole in the bearing, wedge it there so it cant fall out. Heat the crank just a little around the bearing (use an ordinary propane or butane burner) oxy will do but don't go crazy, this will release any loctite that may have been inserted with the bearing, and also open up the spigot recess in the crank, then get funky with the slide hammer.
Built, not bought.
Who is online
Users browsing this forum: No registered users and 6 guests