Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
stainless custom snorkel
Moderator: Micka
stainless custom snorkel
just installed a new custom made stainless steel snorkel to my 87 classic, went in ok without any major problems and looks pretty neat too, if anyone wants the pics of a description on how i did it .. email me
Virgins !!!
someone has to go first !
someone has to go first !
my snorkel
The pipe cost me bout 200 bucks and the hose was about 40 bucks .. and all i need now is the safari intake for the top.
the grill behind the bonnet will have a polished stainless mesh instead of the crap plastic which is currently there, to match the snorkel
will send pics to Mike when it is done and he can post them, i pick up my new Lightforce spotties on monday ... woo hoo .. then i will have 10 light facing forward...
" if i dont see ya .. u wernt there"
cheers
the grill behind the bonnet will have a polished stainless mesh instead of the crap plastic which is currently there, to match the snorkel
will send pics to Mike when it is done and he can post them, i pick up my new Lightforce spotties on monday ... woo hoo .. then i will have 10 light facing forward...
" if i dont see ya .. u wernt there"
cheers
Virgins !!!
someone has to go first !
someone has to go first !
Loanrangie wrote:Steve if the stainless is a bit bling and $$$, then 3" exhaust pipe will do the same just get it powder coated black. Maybe we can get a double order as we are both local.
nick.
Bloody oath mate i'll be in that! what engine u running? i've got the 3.5 carb so im still deciding on how to plumb it any ideas? Not too sure about duelies cos i want to convert to EFI in a couple of years!
Also is 3 inch normal i would have guessed it would have been a bit larger!
Suppose snorkle rams fit on a three inch!
Keep in touch and we might be able to arrange something!
cheers
steve
Here is a couple of photos for you.
Last edited by Maggot4x4 on Sun Dec 19, 2004 9:04 pm, edited 1 time in total.
[quote="Wooders"]If ya want a 4x4 camry go ahead & buy a Patrol or Cruiser.[/quote]Rangie with 80s LC diffs, Isuzu 4bd1, Twin ARB lockers, 8000lb Hi mount warn, 315x75x16 Procomp XTerrains
Stainless Custom Snorkel
My 1976 Series 3 Diesel Landrover (SWB) has had a custom made stainless steel snorkel for over a year - it was made and fiited by Bill Larman for a very reasonable price and works perfectly.
I would put up a photo if I knew how to.
I would put up a photo if I knew how to.
Richard Tye
Melbourne
Land Rovers Owner Club Victoria
Melbourne
Land Rovers Owner Club Victoria
The photo's are of Rangee's snorkle. PM him for more info. Mine is a Rangie spares one and it's on a 4BD1 diesel so I don't think it would help many of you.
[quote="Wooders"]If ya want a 4x4 camry go ahead & buy a Patrol or Cruiser.[/quote]Rangie with 80s LC diffs, Isuzu 4bd1, Twin ARB lockers, 8000lb Hi mount warn, 315x75x16 Procomp XTerrains
Okay, heres some photos of mine. The ducting is flexible 3inch inside diameter, the snorkle itself is 3 inch exhaust pipe with two mandrel bends welded in, and painted black..... The mounts I didn't make, a guy I know had made it, then chopped the bottom off later to use for something else, I just put the bottom bend back on. Around the (massive!) hole in the scuttle panel is some flare piping I had left over.
You need to cut a section out of your bonnet, and also at the front of the scuttle panel, where the ducting comes through in mine (and obviously one for the snorkle to poke through).
Excuse the yellow wiring next to the duct, its recent and I haven't got round to putting conduit over it yet.
You need to cut a section out of your bonnet, and also at the front of the scuttle panel, where the ducting comes through in mine (and obviously one for the snorkle to poke through).
Excuse the yellow wiring next to the duct, its recent and I haven't got round to putting conduit over it yet.
You do not have the required permissions to view the files attached to this post.
84 Rangie, 3 inch spring lift, 2 inch body, Megasquirted 4.6, R380, rear Maxi, 34x11.5 JT2s. Simex FM installed.
What about this r/h snorkel i've made, to match my l/h Rangie Spares one. The one in the photo is the dummy i made for the fibreglassers to take a mould of, the mould will be finished tomorrow.
You do not have the required permissions to view the files attached to this post.
Last edited by 6.5 rangie on Tue Jan 24, 2006 8:28 pm, edited 1 time in total.
Nice work Ranging.
It's been a while since I looked under the bonnet of a carb rangie, but regarding routing of flexy pipe - can the centre air filter be flipped over so intake is pointing towards windscreen? Maybe even reverse alloy U-bends as well, if not enough room for centre pipe?
I dunno if possible and just thinking out aloud but it could neaten up the intake routing a bit, save pipe dangling over motor...
Hardy
It's been a while since I looked under the bonnet of a carb rangie, but regarding routing of flexy pipe - can the centre air filter be flipped over so intake is pointing towards windscreen? Maybe even reverse alloy U-bends as well, if not enough room for centre pipe?
I dunno if possible and just thinking out aloud but it could neaten up the intake routing a bit, save pipe dangling over motor...
Hardy
Who is online
Users browsing this forum: No registered users and 17 guests