I know these come standard in some mq's but mine doesnt have one and i was wondering does anyone have one that i could buy and are they difficult to install??
Marc
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
MQ Diesel tacho
Tacho
In order to have a tacho dash you must get the dash and the sensor in the front of the motor near the crank pulley and injection ump case. Mq's never came out in turbo and yet still had sensor hole covered by plate - however upon attempting to fit the sensor in the hole he hole was found to be too small... its ok with the Mk diesel as they introduced the TD varient with Mk's and enlarged the hole from factory.....
There are aftermarket tacho kits for a diesel that runs off a sensor but they are rather expensive at over $450 for tacho and sensor....
If you try to get factory sensor form nissan its gonna put you back about $197 I think it was....
Hope it helped.
There are aftermarket tacho kits for a diesel that runs off a sensor but they are rather expensive at over $450 for tacho and sensor....
If you try to get factory sensor form nissan its gonna put you back about $197 I think it was....
Hope it helped.
MQ/MK Parts for sale!!!! See for sale section!
Shark,
Do a search on this topic mate.
There are previous threads on this.
I even remember asking the same question back when i was just starting on patrols.
As patroldude said, u need teh sensor that goes into the front crankcase.
and that wont fit into the Stock MQ sd33 without mods.
MQs were never released with the tacho on deisels. Only the MKs, and even then it was far more comon in turbo diesels than std SD33.
aftermarket kits arnt worth it.
Personally u dont need one. SD33s will rev quite high/ I can garuntee u that u can safely push it harder than u have thus far.
And when they hit there rev peak, all they do is wont go any harder no matter how hard u try, and start getting hot.
in a petrol motor when u hit redline they clunk and kill acceleration.
they really arnt worth the effort. I put a petrol tacho Into My SD33 diesel dash for the V8 and it works fine, so the dash doesnt need mods as it supports the petrol tacho. But u will need the deisel tacho and sender for this job.
screwy
Do a search on this topic mate.
There are previous threads on this.
I even remember asking the same question back when i was just starting on patrols.
As patroldude said, u need teh sensor that goes into the front crankcase.
and that wont fit into the Stock MQ sd33 without mods.
MQs were never released with the tacho on deisels. Only the MKs, and even then it was far more comon in turbo diesels than std SD33.
aftermarket kits arnt worth it.
Personally u dont need one. SD33s will rev quite high/ I can garuntee u that u can safely push it harder than u have thus far.
And when they hit there rev peak, all they do is wont go any harder no matter how hard u try, and start getting hot.
in a petrol motor when u hit redline they clunk and kill acceleration.
they really arnt worth the effort. I put a petrol tacho Into My SD33 diesel dash for the V8 and it works fine, so the dash doesnt need mods as it supports the petrol tacho. But u will need the deisel tacho and sender for this job.
screwy
TUFF TRUCK TEAM OPPOSITE LOCK Proudly Sponsored By:
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Opposite Lock Narellan, Lightforce Australia, Offroad Systems, Judd Panels, Townsend Signs, RDG Engineering, Central Safety Workwear
Who is online
Users browsing this forum: No registered users and 151 guests