Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Hydraulic clutches??

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 87
Joined: Mon Apr 19, 2004 7:48 pm
Location: QLD...Where else would you want to live??

Hydraulic clutches??

Post by Whitey »

I've put in a toyota 4AGE engine into my suzuki sierra and it has a celica 5spd behind it that has a hydraulic clutch instead of the normal cable one. Problem is, after the conversion, there is hardly any clutch, and I'm having trouble bleeding the system. It seems like i've bled a few litres through it but it doesn't help. Have other people had this problem, or am I over looking something simple??? There is just enough clutch pressure to put it into gear and change up gears but I can't change back gears (eg 3rd to 2nd) any ideas or other techniques to bleed the system?
92 Sierra
Toyota 4AGE
2 inch body lift
2 in Dobinson springs
31 Bfg's A/T
Rear ARB locker
Sliders
Top
Posts: 5179
Joined: Fri Dec 05, 2003 8:15 pm
Location: Brisbane Australia

Post by Shadow »

maybe your slave cylinder rod is too short?

maybe your pedel is hitting the floor before the full stroke of the master cylinder., try adjusting the push rod into the master cylinder longer, and rais the upper stop of the clutch pedal
Top
Posts: 527
Joined: Sat Oct 02, 2004 3:55 pm
Location: Brisbane

Post by adam.s »

did you bench prime the master cylinder?

you can prime the hydrolic piping while its in the car if you use a syringe (big one obviously)

takes about 30 seconds to bleed the system if you bench prime the cylinder and system, or it willt ake 15-20 minutes of you pumping like crazy.

you are probably doing it, its just taking a long time.
Top
Posts: 1768
Joined: Sun Mar 14, 2004 11:51 am
Location: Weipa

Post by crankycruiser »

Do u know if the clutch is any good???
Top
Posts: 87
Joined: Mon Apr 19, 2004 7:48 pm
Location: QLD...Where else would you want to live??

Post by Whitey »

Yeah, the clutch is fine. Everything worked before the conversion, it looks like Shadow's in the know. The pin that locks the slave cylinder rod to the clutch pedal was missing/fallen out so the pedal is traveling too much before pushing into the cylinder... Thanks for your help..
92 Sierra
Toyota 4AGE
2 inch body lift
2 in Dobinson springs
31 Bfg's A/T
Rear ARB locker
Sliders
Top
Posts: 13
Joined: Tue Apr 27, 2004 9:19 pm
Location: Hervey Bay

Post by emkate »

foad wrote:did you bench prime the master cylinder?

you can prime the hydrolic piping while its in the car if you use a syringe (big one obviously)

takes about 30 seconds to bleed the system if you bench prime the cylinder and system, or it willt ake 15-20 minutes of you pumping like crazy.

you are probably doing it, its just taking a long time.



Could you please explain exactly how you bench prime the master cylinder, I'm having trouble with mine and I'm thinking this may be the cause. Thanks.
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 3 guests