thanks for that Ruff.
so being as handy with the tools as you seem to be have you made external ones or not?
if so did you ever drive these on the road?I'm looking at making some external ones after what i've read about the internals.
Have you got any tips that you would like to pass on. they are are going on 15x8 steelies with 36" simex's.
thanks for your time
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
d.i.y beadlocks
Moderators: toaddog, TWISTY, V8Patrol, Moderators
God of Magnificant Ideas!
I looked into this 6 months ago...... Thought being removing the Simex tubes and replacing them with beadlocks.
The local "Speedway Shop" sells kits for DIY beadlocks and from memory they went for around.....
Steel inner, Steel outer setup = $ 80.00 a rim
Steel inner, Alloy outer setup = $120.00 a rim
The Alloy set was predrilled but didnt come with nuts n bolts.
The steel set wasnt drilled and again no nuts n bolts.
I've done 2 sets of rims ( one of each type) now and cant find any major differances between the steel or alloy setup. I also used a mig on the first set and went to arc on the second set ( ran out of argon on the mig), and I must admit that the arc welding was a much better job both in looks and strength in the final product even though it took an extra hour or so compared to the miged set to actually weld up.
A simple way to "true up " the rim was to .....
tack the beadlock on to the rim,
fit the rim onto the jacked up rig,
spin it slowly and using a brick sitting on the floor as a "guide for trueing",
add a few extra tacks as I went.
once I was happy with the alignment I welded 2" then spun the rim a 1/4 of a turn then welded a further 2".... and so on.
The rims came up really well and I even took em down to the local tyre joint and had him spin em on the tyre balancer ( minus tyres ) so I could see how far out of wack they were...... must have fluked both sets
as neither had any distortion or out of balance effect.!
Kingy
p/s I sold both sets for much more than I would have valued em at and I still dont have a set for myself.....
I'll stick with the Simex tubes for now
The local "Speedway Shop" sells kits for DIY beadlocks and from memory they went for around.....
Steel inner, Steel outer setup = $ 80.00 a rim
Steel inner, Alloy outer setup = $120.00 a rim
The Alloy set was predrilled but didnt come with nuts n bolts.
The steel set wasnt drilled and again no nuts n bolts.
I've done 2 sets of rims ( one of each type) now and cant find any major differances between the steel or alloy setup. I also used a mig on the first set and went to arc on the second set ( ran out of argon on the mig), and I must admit that the arc welding was a much better job both in looks and strength in the final product even though it took an extra hour or so compared to the miged set to actually weld up.
A simple way to "true up " the rim was to .....
tack the beadlock on to the rim,
fit the rim onto the jacked up rig,
spin it slowly and using a brick sitting on the floor as a "guide for trueing",
add a few extra tacks as I went.
once I was happy with the alignment I welded 2" then spun the rim a 1/4 of a turn then welded a further 2".... and so on.
The rims came up really well and I even took em down to the local tyre joint and had him spin em on the tyre balancer ( minus tyres ) so I could see how far out of wack they were...... must have fluked both sets
as neither had any distortion or out of balance effect.!
Kingy
p/s I sold both sets for much more than I would have valued em at and I still dont have a set for myself.....
I'll stick with the Simex tubes for now
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
thanks mate
thanks mate have you got any pic's of the alloy ones?
If not what about contact details to the shop that you get them.
Alloy ones would be nice?
Thanks mate
p.s what thickness was the material?
If not what about contact details to the shop that you get them.
Alloy ones would be nice?
Thanks mate
p.s what thickness was the material?
God of Magnificant Ideas!
Sorry ..... no pics !
"WIGGY'S SPEEDWAY SPARES"
42 VICTORIA STREET,
COBDEN
VIC
phone: 03 55 95 1011
ph/fax: 03 55 95 1100
Mobile: 0407 041 145
OR -----------------------------------------------------------------
"COBDEN AUTO MART"
1232 CAMPERDOWN ROAD,
COBDEN
VIC
phone: 03 55 2285
mobile: 0417 107 377
Both guys are ex speedway drivers and now work as "spare parts suppliers" only for speedway cars and predominately for sprintcars.
If they dont have any stock on hand then its usually a 2 week wait for new stock........ its also nearing the end of the sprincar season so they may have "reduced" their stock on hand.
Kingy
"WIGGY'S SPEEDWAY SPARES"
42 VICTORIA STREET,
COBDEN
VIC
phone: 03 55 95 1011
ph/fax: 03 55 95 1100
Mobile: 0407 041 145
OR -----------------------------------------------------------------
"COBDEN AUTO MART"
1232 CAMPERDOWN ROAD,
COBDEN
VIC
phone: 03 55 2285
mobile: 0417 107 377
Both guys are ex speedway drivers and now work as "spare parts suppliers" only for speedway cars and predominately for sprintcars.
If they dont have any stock on hand then its usually a 2 week wait for new stock........ its also nearing the end of the sprincar season so they may have "reduced" their stock on hand.
Kingy
[color=blue][size=150][b]And your cry-baby, whinyassed opinion would be.....? [/b][/size][/color]
Who is online
Users browsing this forum: No registered users and 2 guests