Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

ARC WELDING

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 191
Joined: Mon Nov 29, 2004 5:42 pm
Location: melbourne

ARC WELDING

Post by kranked_dirt »

Excuse my ignorance :oops: ... can aluminium be welded with an arc welder, if so what electrodes do i use, any special way it should be done??

cheers
went there dressed up, came back messed up

81 FJ40 hardtop - Lexus 1UZ-FE conversion underway
Top
Posts: 141
Joined: Fri Nov 12, 2004 4:46 pm
Location: Newcastle

Post by mickbeny »

Hi all...K-D,No you cant weld alluminium with an electrode,you caN mig and tig[AC hf only]Aluminium though.
PEACE...
Top
Posts: 3739
Joined: Sat Dec 11, 2004 10:10 pm

Post by mickyd555 »

to mig weld aluminium is preety hard if you dont know what your doing......how do i know this......cause i tried and failed. if your gonna mig it you need straight argon gas, and from memory lots of heat. tig is the way to go, and if its just to repair a bullbar or something, i dont think it would be costly to get it done by a pro.... good luck
Top
Posts: 4426
Joined: Mon Mar 22, 2004 4:39 pm
Location: Sunshine Coast

Post by bru21 »

ally is ok with mig or tig. cleanleness cannot be more important. the weld puddle tends to pool without flowing on if there is contamination present, and often drops through. be clean buy a new wirw brush and use it for ally only, removing anodizing helps too.

cheers bru
ADHD Racing would like to thank
Mrs Bru @ Sunshine Coast Developmental Physiotherapy - www.scdphysio.com.au , Ryano @ Fourbys www.generaltire.com.au Blitzkrieg Motorsport
Top
Posts: 342
Joined: Sun Sep 19, 2004 3:49 pm
Location: gippsland vic

Post by ratboy »

bru21 wrote:ally is ok with mig or tig. cleanleness cannot be more important. the weld puddle tends to pool without flowing on if there is contamination present, and often drops through. be clean buy a new wirw brush and use it for ally only, removing anodizing helps too.

cheers bru





hes on the money
ok it was me
Top
Posts: 3722
Joined: Sat Jan 18, 2003 7:32 pm
Location: perth wa

Post by bazooked »

oh and heat is not the key for ali it will drop away without warning, u cant see the colour change like in steel.
Top
Posts: 243
Joined: Thu Jul 15, 2004 9:21 am
Location: Townsville

Post by Dane »

I have seen arc welder electrodes for aluminium, but have not used them. Mig welding ally is best suited to heavier sections (+6mm) and as well as bru's comments, pre heating the job with oxy helps a great deal. Definitely tig for the lighter stuff. Use a stainless steel wire brush.
Top
Posts: 73
Joined: Sun Nov 16, 2003 5:08 pm
Location: vic

Post by thomo »

Plus you need a high freq tig for ally dont think to many people have them in there shed.
Top
Posts: 32
Joined: Thu Feb 17, 2005 7:39 pm
Location: Sydney

Post by Major60 »

Dane wrote:I have seen arc welder electrodes for aluminium, .


Yes they exist, ..... and I wouldn't rust any critical welds with them...
Top
Posts: 2031
Joined: Tue Oct 22, 2002 10:49 am
Location: On a mission...

Post by Damo »

Dane wrote:Use a stainless steel wire brush.


Yes! And if it's been oily/greasy you may need to give it a wipe with metho to get it nice & clean.
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 1 guest