Can anyone tell me what is involved with changing the rubber CV boot on the drivers side. I have a tear in the inner CV boot.
I've never played with CV's before.
I got quoted $15 for the inner and another $15 for the outer from Autobarn
Thanks.
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Changing a CV boot on a 97 Rodeo???
Moderator: Moderators
Changing a CV boot on a 97 Rodeo???
Land Rover Discovery series 1 V8
Utemad,
If you like, PM me your email and I will send you a couple of pages printed out of the TF Rodeo Service manual CD. I tried to post them on the forum but PDF files are not allowed (or at least thats the response I got).
They are typical lame service manual diagrams but may point you in the right direction.
Cheers
Rainsey
If you like, PM me your email and I will send you a couple of pages printed out of the TF Rodeo Service manual CD. I tried to post them on the forum but PDF files are not allowed (or at least thats the response I got).
They are typical lame service manual diagrams but may point you in the right direction.
Cheers
Rainsey
PM sent. Like I mentioned in the PM I have a Rodeo workshop CD that does not work anymore. It used to but now I get an error message that says:
16 Bit Windows Subsystem
C:\Windows\System32\Autoexec.NT
The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose close to terminate the application.
Anyone know what the hell that means?
16 Bit Windows Subsystem
C:\Windows\System32\Autoexec.NT
The system file is not suitable for running MS-DOS and Microsoft Windows applications. Choose close to terminate the application.
Anyone know what the hell that means?
Land Rover Discovery series 1 V8
Replaced the CV boots this morning 
Took me exactly 3 hours however I can see that it could be shortened. For example it took me 45mins just to get the upper ball joint off the upper control arm
It is very straight forward and I would recommend to anyone that you can do it yourself. The only CV I have ever seen before is on the internet and I managed it. The only problems I had other than chasing the steel balls down the driveway numerous times
was doing up those steel band things that hold the boots on. I managed to stuff the one that holds the inner boot to the diff housing so that is held on by a zip tie atm. The one on the brake end is not so flash either but is on all the same. I'll get two more bands and fix them before I go 4bying next. If you are tightening them with cutters or pliers then I reckon (after I busted two) that the best way is to push against the clippy bit with a screwdriver and pull the tab with pliers or cutters. You'll know what I mean when you see the band clamps.
The only thing I did differently to the 4x4wire HowTo was to undo the top nut holding the shock absorber in and then moved the shock out of the way. I would have removed it all together had I been able to undo the lower bolt.
All in all it was a fairly easy job
Give it a go.
Took me exactly 3 hours however I can see that it could be shortened. For example it took me 45mins just to get the upper ball joint off the upper control arm
It is very straight forward and I would recommend to anyone that you can do it yourself. The only CV I have ever seen before is on the internet and I managed it. The only problems I had other than chasing the steel balls down the driveway numerous times
was doing up those steel band things that hold the boots on. I managed to stuff the one that holds the inner boot to the diff housing so that is held on by a zip tie atm. The one on the brake end is not so flash either but is on all the same. I'll get two more bands and fix them before I go 4bying next. If you are tightening them with cutters or pliers then I reckon (after I busted two) that the best way is to push against the clippy bit with a screwdriver and pull the tab with pliers or cutters. You'll know what I mean when you see the band clamps.
The only thing I did differently to the 4x4wire HowTo was to undo the top nut holding the shock absorber in and then moved the shock out of the way. I would have removed it all together had I been able to undo the lower bolt.
All in all it was a fairly easy job
Give it a go.
Land Rover Discovery series 1 V8
Doh...
O/K... im next at doing this. Just has the suspension upgraded and noticed my driverside boot is ripped in two.
One thing that I have learn't over the years.... cable ties are your best friend... it is amazing what you can hold together with them... including a CV boot after breaking the steel clamp.
Might only be short term but I carry a load of them in my under rear seat storage compartment ( raised my rear seats so the kids did not feel like midgets) for times like this.
I'll take your advice on board.
Cheers
Rainsey
O/K... im next at doing this. Just has the suspension upgraded and noticed my driverside boot is ripped in two.
One thing that I have learn't over the years.... cable ties are your best friend... it is amazing what you can hold together with them... including a CV boot after breaking the steel clamp.
Might only be short term but I carry a load of them in my under rear seat storage compartment ( raised my rear seats so the kids did not feel like midgets) for times like this.
I'll take your advice on board.
Cheers
Rainsey
rainsey wrote:One thing that I have learn't over the years.... cable ties are your best friend...
Zip ties rule!!! On my ute I have the front licence plate, inner CV boot, rear canopy brake light, trailer light socket, fridge power socket and of course kms of wiring all held on with zip ties. Of course it's temporary
rainsey wrote:under rear seat storage compartment ( raised my rear seats so the kids did not feel like midgets) for times like this.
I was thinking about cutting a big hole under the rear passenger bench seat to make a storage compartment like the existing one for the jack. Seems to be a fair bit of wasted space under there. Also trying to make the rear seat tilt forward like on newer versions. Too hard to adapt a later model backrest though. Shouldn't be too difficult to modify the existing backrest.
Land Rover Discovery series 1 V8
I was originally looking at doing the same but the diesel fule tank is sitting right underneath!
I made a wooden frame that sits between the metal body and the seat. It has a double use, I have a boot load of storage for spare radiator hoses, filters and general bits & pieces (like cable ties), plus the kids can not sit normally without their legs wrapped up. Makes it heaps more comfortable on a long trip.
The back part of the seat I raised by drilling out the spot welded brackets and raising them the height of the wooden base. And extended the lower bolt holes by fabricating some steel extentions.
Works a treat... I'll take some photos and put them up for you to see.
Cheers
Rainesy
I made a wooden frame that sits between the metal body and the seat. It has a double use, I have a boot load of storage for spare radiator hoses, filters and general bits & pieces (like cable ties), plus the kids can not sit normally without their legs wrapped up. Makes it heaps more comfortable on a long trip.
The back part of the seat I raised by drilling out the spot welded brackets and raising them the height of the wooden base. And extended the lower bolt holes by fabricating some steel extentions.
Works a treat... I'll take some photos and put them up for you to see.
Cheers
Rainesy
Temporary Australian
it would probably be a good idea to replace the balljoints at the same time.... an extra cost i know, but easier to do while you have half the front end in bits. in case you are interested, i payed $520 for brand new CV's and axles and boots all assembled......
There is no "I" in Team, but there are 5 in Individual Brilliance
I only did the drivers side but that ball joint looked ok to me. I thought of replacing it anyway but thought it didn't need to be yet.
Rainsey,
Pics of your rear seat would be great but we should probably start another thread for that. I'm investigating the fold forward option again. Hopefully start on it this weekend.
Thanks.
Rainsey,
Pics of your rear seat would be great but we should probably start another thread for that. I'm investigating the fold forward option again. Hopefully start on it this weekend.
Thanks.
Land Rover Discovery series 1 V8
Who is online
Users browsing this forum: No registered users and 0 guests