Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Which diff?

Tech Talk for Rover owners.

Moderator: Micka

Post Reply
Posts: 8459
Joined: Mon Nov 29, 2004 8:15 pm
Location: Townsville

Which diff?

Post by "CANADA" »

whats the easyest way to tell is its a sals' dif or rover???i have centers and housings (minus axles/tubes :bad-words: ) but is there a certain bolt patern or somewhere it will be stamped onthe ring gear or casing?

thanks 'Canada'
[quote="dazza30875"]whats "FAIL" mean[/quote]

[quote="fool_injected"]

Sometimes your funny Canada :D[/quote]
Posts: 141
Joined: Sun Jan 16, 2005 7:22 pm
Location: Gold Coast,Tweed

diff

Post by THE 109 »

salisbury diffs have a removable 10bolt plate on the back of the diff housing to allow the removal of the diff centre.the centre is larger than the rover type and has 4 planet gears,rover diffs normally only have 2 planet gears.the salisbury ring and pinion are once again larger than the rover one.
Posts: 3278
Joined: Mon Mar 03, 2003 9:03 pm
Location: St Helena, Melbourne.

Post by Loanrangie »

A salisbury has a removeable pressed metal diff cover and the center is cast and not removeable.
Saddle up tonto, its the not so loanrangie! . 98 TDI DISCO lightly modded with more to come.
Posts: 8459
Joined: Mon Nov 29, 2004 8:15 pm
Location: Townsville

Post by "CANADA" »

does the sals center fit in the rover axle?
[quote="dazza30875"]whats "FAIL" mean[/quote]

[quote="fool_injected"]

Sometimes your funny Canada :D[/quote]
Posts: 1614
Joined: Fri Feb 21, 2003 8:44 pm
Location: Melbourne

Post by landy_man »

no way.. the sals is pretty chunky...
go stick your head under a pre 02 defender and look at the rear diff compared to the front diff... the housings on a Sals are huge..
Posts: 3278
Joined: Mon Mar 03, 2003 9:03 pm
Location: St Helena, Melbourne.

Post by Loanrangie »

Plus the carrier portion of a sals is cast with the center housing so cannot be removed as such, i believe that some dana parts will fit though.
Saddle up tonto, its the not so loanrangie! . 98 TDI DISCO lightly modded with more to come.
Posts: 231
Joined: Mon Dec 20, 2004 9:43 am
Location: lost in my pile of parts

Post by Tim D »

as i have replaced a R & P in my old s3 i measured the ring and it was 12.5 inches in diametre :shock: not shore about the rover ones. ;)
Posts: 500
Joined: Tue Nov 04, 2003 2:00 am
Location: Canada

Post by red90 »

The "Salisbury" axle uses a Dana 60 ring and pinion. This is a 9-3/4" hypoid gear. The "Rover" diff is an 8-1/2" spiral bevel R&P.

Dana 60
Image[/url]
[color=red]1991 Landrover 90 ex-MOD[/color]
Posts: 21
Joined: Thu Feb 24, 2005 12:20 pm
Location: Brisbane

Post by b_mac »

The Salisbury diff housing has to be spread to remove the carrier. The spreader tool uses the two sockets either side of the diff, but big mongrel screwdrivers will also to the trick :lol:



Bruce.


Installation is the reverse of removal - yeah right.
Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests