has anyone done this conversion or seen it done??? we sat the engine and gearbox in today and the cross member is way to high for the sierra gearbox so it doesnt fit in.wot would be the best thing to do cut the cross member?can i cut that cross member? or lift the body it would hav to be a fair way or something else??? the sump is to close to the diff at the moment but reset springs should solve that problem i hope and is there any other problems im likely to encounter? any input appreciated
thanks
Brad
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
1 Litre Sierra into LJ50
Moderators: toaddog, TWISTY, V8Patrol, Moderators
1 Litre Sierra into LJ50
The road to enlightenment requires Four Wheel Drive
OK....I'll reply to your question !!!
GROVER - LJ80 (Melbourne)
Purchased with a Corolla 4K Conversion.
It now sports a 1.3L Sierra Engine coupled with a 5 Speed Sierra Manual Box and T-Case.
Kenn (the owner) says if you have to cut the cross member....then cut it ! He did not have to modify the tunnel too much (just a little wider in a couple of spots if I recall).
It also has a 2" body lift which helps everything fit under the body!!
Couple of things to watch out for are :
1. Gear stick location - I think there was some modification to the hole
2. Clutch plate activation
3. Steering box - Kenn's unsure as his already had the 4K conversion.
4. If you drop in a 1L, don't forget about maybe getting the 1L radiator. Unsure if it will fit....he thinks not likely, so you may need a custom radiator.
That's all he could think of at the moment, too busy concentrating on the next project for Grover !!!
1600 16V with 4 speed electronic auto, Vitara rear diff (with ARB Locker) and a modified 1.3 LJ80 front diff with Vitara centre (also running ARB Locker) !!!
Hope this helps, for more info, PM me and I'll give you his contact number in Mebourne
GROVER - LJ80 (Melbourne)
Purchased with a Corolla 4K Conversion.
It now sports a 1.3L Sierra Engine coupled with a 5 Speed Sierra Manual Box and T-Case.
Kenn (the owner) says if you have to cut the cross member....then cut it ! He did not have to modify the tunnel too much (just a little wider in a couple of spots if I recall).
It also has a 2" body lift which helps everything fit under the body!!
Couple of things to watch out for are :
1. Gear stick location - I think there was some modification to the hole
2. Clutch plate activation
3. Steering box - Kenn's unsure as his already had the 4K conversion.
4. If you drop in a 1L, don't forget about maybe getting the 1L radiator. Unsure if it will fit....he thinks not likely, so you may need a custom radiator.
That's all he could think of at the moment, too busy concentrating on the next project for Grover !!!
1600 16V with 4 speed electronic auto, Vitara rear diff (with ARB Locker) and a modified 1.3 LJ80 front diff with Vitara centre (also running ARB Locker) !!!
Hope this helps, for more info, PM me and I'll give you his contact number in Mebourne
[color=orange] BESTY [/color]
GU4800
GU4800
Who is online
Users browsing this forum: No registered users and 2 guests