Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Rear lower control arms

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Posts: 314
Joined: Sun Oct 17, 2004 7:46 pm
Location: Melbourne

Rear lower control arms

Post by AndrewPatrol »

A mate with a GQ has bent one and is looking to replace them with better ones. Someone told him that if he goes too strong then it can place the stress further down the line. But being in the position they are and if one breaks the consequences, wouldnt it be better to have the strongest arms he can afford? Advice greatfully accepted.
Thanks
Posts: 4494
Joined: Mon Nov 25, 2002 9:51 pm
Location: Golden Square

Post by turps »

All the aftermarket ones are very strong. I have the mal leslies ones on my shorty. They where on cheezy's mav before he got serious (well it still ran 39"tyres) and removed them, so they have coped alot of abuse and teh are still straight.
Others are
Snakeracing
3rd Productions
Cheezy Racing (need to buy via there dealers - OnTrack (east Keilor))
BBM
no doubt there are others.
THOUGHT FOR THE DAY....
Posts: 1781
Joined: Mon May 17, 2004 10:01 pm
Location: Geelong

Post by beretta »

I've got some cheezy ones and they're much, much beefier than the stockies, I would recomend em, also slightly longer to suit 4 to 6 inch lift. I brought mine off someone from here, can't remember how much off the shelf, might have been around the $600 mark, someone might be able to correct me here?
Posts: 55
Joined: Wed Jan 14, 2004 9:06 pm

rear arms

Post by bigpig »

ihave a gu and run 3rd's upper and lower arms love the shit i put them through :lol:

Slaming into rocks and bouncing on them has had no efect on them yet bar a few scratches :armsup: :armsup: :onfire:
Posts: 3054
Joined: Mon Nov 03, 2003 4:30 pm
Location: Melbourne

Post by hottiemonster »

beretta wrote:I've got some cheezy ones and they're much, much beefier than the stockies, I would recomend em, also slightly longer to suit 4 to 6 inch lift. I brought mine off someone from here, can't remember how much off the shelf, might have been around the $600 mark, someone might be able to correct me here?


brand new longer ones (16 mm) with supplying your own bushes from the old ones of brand new bushes costs $200 from cheezy.
Gq ute new built
Posts: 1781
Joined: Mon May 17, 2004 10:01 pm
Location: Geelong

Post by beretta »

There you go, I was way off! I reckon they're worth all of that!
Posts: 2097
Joined: Mon Jun 14, 2004 8:06 pm
Location: Land of Plenty

Post by blkmav »

I have some Snake Racing adjustable lower arms with mogs joints for sale cheap. PM me if your mate is interested.

Image
Image
Image
Weekdays - Prado GXL D4D with some stuff
Weekends - Mav shorty with lots of stuff
Posts: 55
Joined: Wed Jan 14, 2004 9:06 pm

Post by bigpig »

why are you selling :?: :roll:
Posts: 2097
Joined: Mon Jun 14, 2004 8:06 pm
Location: Land of Plenty

Post by blkmav »

Want to go back to bushes
Weekdays - Prado GXL D4D with some stuff
Weekends - Mav shorty with lots of stuff
Posts: 2853
Joined: Tue Nov 30, 2004 10:55 pm
Location: All over the world or your mum

Post by toughnut »

Too rough a ride? Mog joints at both ends aren't always a good idea. You need to have some give in the suspension components or you'll break something. Having adjustable on the lower can creat problems as well sometimes if you bash them on a rock. Strong arms though. :D
j-top paj wrote:gayer than jizz on a beard
http://www.outerlimits4x4.com/viewtopic ... 6&t=231346
Posts: 2097
Joined: Mon Jun 14, 2004 8:06 pm
Location: Land of Plenty

Post by blkmav »

Nah they 'clunk' as they take up the slack and it annoys me. A bit like when you tow a trailer and the trailer hitch moves on the ball.
Weekdays - Prado GXL D4D with some stuff
Weekends - Mav shorty with lots of stuff
Posts: 55
Joined: Wed Jan 14, 2004 9:06 pm

Post by bigpig »

Too rough a ride? Mog joints at both ends aren't always a good idea. You need to have some give in the suspension components or you'll break something. Having adjustable on the lower can creat problems as well sometimes if you bash them on a rock. Strong arms though.


:D :finger:

I bet the f***ers are as noisy as f**k i have been in car fiited with that shit but never again :bad-words: and also seen 2 bent Cookie :shock:
Posts: 372
Joined: Mon Nov 03, 2003 10:12 pm
Location: melbourne. sth eastern subs

Post by bagsy »

If you buy the arms with no bushes , how hard is it to swap my ones into the new arms. My bushes are in good condition but worried I will destroy them trying to press them out.
http://www.biders4wd.com/
http://www.autobalance.com.au/
www.4bfabrications.com.au
Posts: 2853
Joined: Tue Nov 30, 2004 10:55 pm
Location: All over the world or your mum

Post by toughnut »

A piece of 50mm nominal bore medium black tube will fit quit well without damaging your bushes. ;)
j-top paj wrote:gayer than jizz on a beard
http://www.outerlimits4x4.com/viewtopic ... 6&t=231346
Posts: 55
Joined: Wed Jan 14, 2004 9:06 pm

bushes

Post by bigpig »

why not put new super pro bushes in as they give good flex and drivabilaty :lol: :armsup:
Posts: 2853
Joined: Tue Nov 30, 2004 10:55 pm
Location: All over the world or your mum

Post by toughnut »

Can't remember where else I posted this but I get all my bushes for nothing from ARB here in Townsville They fit out new patrols and give me all the bushes that they keep for nothing. I just pick and choose which ones look the best. They are all fine cause they come out of new or near new vehicles. :D
j-top paj wrote:gayer than jizz on a beard
http://www.outerlimits4x4.com/viewtopic ... 6&t=231346
Posts: 55
Joined: Wed Jan 14, 2004 9:06 pm

bushes

Post by bigpig »

yes genuine flex goo but f**k up easy wy would you tell him to use genuine after telling him how many you go through :?:

As sugested use super pro for flex and driveabilaty :roll:
Posts: 2853
Joined: Tue Nov 30, 2004 10:55 pm
Location: All over the world or your mum

Re: bushes

Post by toughnut »

bigpig wrote:yes genuine flex goo but f**k up easy wy would you tell him to use genuine after telling him how many you go through :?:

As sugested use super pro for flex and driveabilaty :roll:


You need to pay more attention to the posts if you want to sprook off like this. I didn't say how many I go through. If you haven't been through the members section in a while I've been changing setups on my GU cab chassis during the build, hence the change in bushes. The only bushes I've actually replaced because they were stuffed was the OME off set nolathane bushes that crapped out after only 5 months. I haven't had to change a rubber bush yet. ;)
j-top paj wrote:gayer than jizz on a beard
http://www.outerlimits4x4.com/viewtopic ... 6&t=231346
Posts: 221
Joined: Mon Sep 06, 2004 3:29 pm
Location: Sydney

Post by muzza_fattire »

blkmav wrote:Nah they 'clunk' as they take up the slack and it annoys me. A bit like when you tow a trailer and the trailer hitch moves on the ball.


I get the same with some custom arms I have. Can get very annoying.
Mine have a little nipple valve that you can spray aerosols in.
I tried WD40 to stop the squeaking, but now I am trying lithium spray grease to try and dampen the noise a bit.
*****************
'88 GQ SWB TD42
Posts: 1153
Joined: Sat Apr 24, 2004 10:17 am
Location: Gold coast QLD

Post by Madmac »

i attended to mine before i bent one, i welded a piece of 25x25x5mm angle along the top and bottom of my arms, and then added a piece on 30x30mmx 5mm angle along the bottom, havent bent one yet and heaps cheaper than aftermarket ones
Posts: 55
Joined: Wed Jan 14, 2004 9:06 pm

Post by bigpig »

See the last post what a cheep and nasty way to get protection :!:

Who has seen arms like these bake :?: :finger:
Last edited by bigpig on Wed Jun 29, 2005 9:04 pm, edited 1 time in total.
Posts: 686
Joined: Sat Mar 12, 2005 12:34 pm
Location: maitland, nsw

arms

Post by bucketofbolts »

is any one using mal lesie arms, the square ones,
bucketofbolts is sold, :(
Posts: 2492
Joined: Sun Nov 24, 2002 8:57 pm
Location: Melbourne

Re: arms

Post by bazzle »

bucketofbolts wrote:is any one using mal lesie arms, the square ones,


They are rectangular.

I have on 2 vehicles, Turps in Post at top does too.
Ive jacked off them once.. (not jacked off on them :oops:)

Bazzle
Posts: 55
Joined: Wed Jan 14, 2004 9:06 pm

Post by bigpig »

any complaints on 3rd's arm :lol: :armsup: if so post it you have complained about every trailing arm but :2gunfire:
Posts: 686
Joined: Sat Mar 12, 2005 12:34 pm
Location: maitland, nsw

arms

Post by bucketofbolts »

sorry, rectangular, so you recommend them
bucketofbolts is sold, :(
Posts: 55
Joined: Wed Jan 14, 2004 9:06 pm

arms

Post by bigpig »

recomend 3rds go across the road and look at them :oops:
Posts: 686
Joined: Sat Mar 12, 2005 12:34 pm
Location: maitland, nsw

arms

Post by bucketofbolts »

yeah i know there great, but im trying to save money for some tyres, and other stuff i need for the trials
bucketofbolts is sold, :(
Posts: 4494
Joined: Mon Nov 25, 2002 9:51 pm
Location: Golden Square

Re: arms

Post by turps »

bucketofbolts wrote:sorry, rectangular, so you recommend them


Yep I have been very happy with mine. They have been smashed onto rock a number of times with no damage. I am only taking them out (will keep though) to try and fix my pinion angle which is buggered due to higher lift, so they need to be slightly longer.

Not sure on there price as I brought mine 2nd hand. But I dont think they come with bushes. But from another current thread, I have found out these can be gotton for about $30-35 each.
The big chunky bushes from snake racing look pretty good, there $120 for a set of 4 Part no # SRNPRAB.
Bigpig has mentioned some but I dont have any details on those.
THOUGHT FOR THE DAY....
Posts: 2853
Joined: Tue Nov 30, 2004 10:55 pm
Location: All over the world or your mum

Re: arms

Post by toughnut »

turps wrote:
bucketofbolts wrote:sorry, rectangular, so you recommend them


Yep I have been very happy with mine. They have been smashed onto rock a number of times with no damage. I am only taking them out (will keep though) to try and fix my pinion angle which is buggered due to higher lift, so they need to be slightly longer.


You could leave them in and get adjustable uppers ;)
j-top paj wrote:gayer than jizz on a beard
http://www.outerlimits4x4.com/viewtopic ... 6&t=231346
Posts: 4494
Joined: Mon Nov 25, 2002 9:51 pm
Location: Golden Square

Re: arms

Post by turps »

toughnut wrote:
turps wrote:
bucketofbolts wrote:sorry, rectangular, so you recommend them


Yep I have been very happy with mine. They have been smashed onto rock a number of times with no damage. I am only taking them out (will keep though) to try and fix my pinion angle which is buggered due to higher lift, so they need to be slightly longer.


You could leave them in and get adjustable uppers ;)


I could but then that would rotate the axle forwards slightly. Which would make the wheel closure to the front of the guard when flexing and as it is have a contact issue now and the front of the guard has already been trimmed. Where as the rear being straight metal no plastic crap. If it still touches there I will cut more off.
THOUGHT FOR THE DAY....
Post Reply

Who is online

Users browsing this forum: No registered users and 7 guests