Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
vit gbox > sierra engine.
vit gbox > sierra engine.
how much is involved in putting a vit autp or even 5spd behind a 1.3 sierra block ?
HYPOFAB Thanks to:
Polyperformance
Yuri 4x4
Longfield
Re: vit gbox > sierra engine.
A fair bit .. for the additional labour etc ... I would just fit a 1.6 and be done with it ..hypolux wrote:how much is involved in putting a vit autp or even 5spd behind a 1.3 sierra block ?
The top two bolts will fit but will need something to make the gearbox bolt holes smaller.
The lower two will actually be wider than the block on the 1.3 .. so some kind of adapter plate will be needed
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
forget the bolt holes!!! 
have you tried to fit a vitara box into a sierra transmission tunnel? MUCH bigger.
I had to widen the tunnel by 2" to fit my vit box into the sierra. The shifter holes are out by miles aswell.
Can I ask why you want a vit box, but not the engine?
Pics
this shows the unmodified drivers side, and the widened passenger side
Both sides cut
Shifter holes
Welded up both sides.
More work than its worth just to run the crappy 1.3 in front of it.
JMO
Pete
have you tried to fit a vitara box into a sierra transmission tunnel? MUCH bigger.
I had to widen the tunnel by 2" to fit my vit box into the sierra. The shifter holes are out by miles aswell.
Can I ask why you want a vit box, but not the engine?
Pics
this shows the unmodified drivers side, and the widened passenger side
Both sides cut
Shifter holes
Welded up both sides.
More work than its worth just to run the crappy 1.3 in front of it.
JMO
Pete
[url]www.twinstickoffroad.com[/url]
Hay Pete , should call that one Quozy , With that hump ! 
Least its prettier then mine
Think Hypos biulding somthing without a floor !! well sort of,
Would actually be a bit of a pian going the vit on 1.3 block , be hard to get the bolt holes sorted on the bellhousing , not that hard going the other way , mmmm
Least its prettier then mine
Think Hypos biulding somthing without a floor !! well sort of,
Would actually be a bit of a pian going the vit on 1.3 block , be hard to get the bolt holes sorted on the bellhousing , not that hard going the other way , mmmm
Hypo already has the 1.3 but needs a box/ transfer so he was guna get the vit box /not sure wat his plans were with the transfer ...............
but anyway if the swap /mod was easy enuf I think he wasa gunna run it for the time being until funds permitted changin the donk .....
His 1.3l is Jake Lawsons off the board ...........
Dan
but anyway if the swap /mod was easy enuf I think he wasa gunna run it for the time being until funds permitted changin the donk .....
His 1.3l is Jake Lawsons off the board ...........
Dan
[b][i] DAN [/i] [/b]
:silly:
:silly:
Who is online
Users browsing this forum: No registered users and 0 guests