Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Small Block Chevy Ignition

For all things Electrical.

Moderator: -Scott-

Forum rules
Post Reply
Posts: 1949
Joined: Wed Oct 23, 2002 7:44 am
Location: Melbourne, Australia

Small Block Chevy Ignition

Post by MKPatrolGuy »

Does any one know where the wire coming out of the dizzy goes to and how the coil, condesor and ballast resistor are wired up?

TIA
[size=100][url=http://www.vickrawlers.com/]VicKrawlers.com[/url]
[url=http://www.drfwdc.org.au/]Dandenong Ranges 4wd Club[/url][/size]
Top
Posts: 428
Joined: Tue Oct 22, 2002 8:26 am
Location: The Sovereign Nation of Sealabia

Post by 2car »

Dave

I have an HEI distributer which is quite different to what you have. I have a couple of books at home that will have the info that you need. I will have a look when I get time.

I recommend the HEI. You can open the spark gap up by about 0.010" over stock and they don't have an external coil. It will start easier, run better when cold and give a little more power. From memory they retail for less than $300 new.
74 FJ40, 307, Hilux DBC, 35 Claws, welded rear.

'''_ ______
'/|_[_____]__
|?[_L/-\_|o=o|_
?:__;-?__-,==,_
()_)O()_)O== )_)
Top
Posts: 1949
Joined: Wed Oct 23, 2002 7:44 am
Location: Melbourne, Australia

Post by MKPatrolGuy »

That would be great, thanks.

I will eventually go HEI, probably when I go to straight gas. But first I just have to get it running and the conversion finished :roll:
[size=100][url=http://www.vickrawlers.com/]VicKrawlers.com[/url]
[url=http://www.drfwdc.org.au/]Dandenong Ranges 4wd Club[/url][/size]
Top
Posts: 309
Joined: Tue Dec 03, 2002 11:43 am
Location: SOMEWHERE IN VICTORIA

Post by TUFF MAV »

Dave

The wire from the dizzy is hooked to the negative side of the coil. The condensor is bolted to earth on dizzy and hooks to wire coming out of dizzy. Ballast resistor will need 12 volt ignition hooked up to one side of resistor. Other side goes to the positive side of ignition coil.

Hope this helps.

Kyle
BUGGERED IT'S A TOYOTA THING
Top
Posts: 1949
Joined: Wed Oct 23, 2002 7:44 am
Location: Melbourne, Australia

Post by MKPatrolGuy »

You Champ, I'll see if I can get the bucket of bolts started tomorrow, hasn't got an exhaust yet :twisted:
[size=100][url=http://www.vickrawlers.com/]VicKrawlers.com[/url]
[url=http://www.drfwdc.org.au/]Dandenong Ranges 4wd Club[/url][/size]
Top
Posts: 428
Joined: Tue Oct 22, 2002 8:26 am
Location: The Sovereign Nation of Sealabia

Post by 2car »

what he said.
74 FJ40, 307, Hilux DBC, 35 Claws, welded rear.

'''_ ______
'/|_[_____]__
|?[_L/-\_|o=o|_
?:__;-?__-,==,_
()_)O()_)O== )_)
Top
Posts: 1949
Joined: Wed Oct 23, 2002 7:44 am
Location: Melbourne, Australia

Post by MKPatrolGuy »

2car wrote:what he said.
:)
[size=100][url=http://www.vickrawlers.com/]VicKrawlers.com[/url]
[url=http://www.drfwdc.org.au/]Dandenong Ranges 4wd Club[/url][/size]
Top
Post Reply

Return to “Auto Electrical”

Who is online

Users browsing this forum: No registered users and 11 guests