Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Quick gearbox question.

Tech Talk for Suzuki owners.

Moderators: lay80n, sierrajim

Post Reply
Posts: 126
Joined: Sat Feb 26, 2005 7:46 pm
Location: Melbourne

Quick gearbox question.

Post by 87suzi »

Just wondering, is there any way of telling the condition of a gearbox while out of the car. I just swapped over my gearbox cause I thought it was better than my one, and now it's crunching 1st and 3rd. My dad said that should be the synchros. I wanna put the old one back in but I don't know whether it's noisy or not (shot bearings). Is there any way of telling before I swap them over?

Also, very important question. For as long as I can remember, when lifting the clutch in neutral the car sounds different. In neutral with the clutch in the only sound is that of the engine, but lift the clutch and on my old box I used to get a faint little noise. On the box I got now it's tonnes worst. Is this normal?

Oh also, by turning the input shaft, the output shaft turns immediately with little or no play, which is good, but I get a little rattle as I turn it back and forth, is this normal?
Posts: 3513
Joined: Tue Feb 15, 2005 12:52 am
Location: Perth, WA

Post by alien »

i didnt think the sierra box had snychro???

if its tcase internals though i have some spare 1.3L ones... you could buy them and go 3rd time lucky? =D
The worst thing about censorship is ███████.
Posts: 3722
Joined: Sat Jan 18, 2003 7:32 pm
Location: perth wa

Post by bazooked »

all 1.3 sierra boxes have syncros, the nosie from ur clutch pedal is ur thrust bearing, while its apart put a new 1 in there, and the play in the input shaft is normal because there is 1 bearing supporting it , the front of the input is supported by the pilot bearing in ur flywheel so check that out as well.
Posts: 126
Joined: Sat Feb 26, 2005 7:46 pm
Location: Melbourne

Post by 87suzi »

bazooked wrote:all 1.3 sierra boxes have syncros, the nosie from ur clutch pedal is ur thrust bearing, while its apart put a new 1 in there,
I'm not too sure what to think about that mate cause this is after putting a clutch kit into it which comes with the bearing. The thrust bearing is the one that pushes out yeah? Anyways, after putting the new gearbox in, today I put in the old one again and it pretty much goes sweet as. Same noise when the clutch pedal is up, but nowhere near as bad.
Posts: 575
Joined: Sun Mar 13, 2005 9:09 pm
Location: Kingston, Tas

Post by derelict_frog »

Yea mine makes a slight noise with the clutch out and its in neutral, i just though it was normal, its pretty quiet on mine...
Posts: 13
Joined: Sat Mar 19, 2005 3:26 pm
Location: Brissy QLD

Post by tinyterror »

its is quite normal to hear a very slight whirring noise when you take your foot of the clutch in neutral as your gearbox internals start to spin, they just have no load on them. You will find any car makes a different sound in the box when liftng or depressing the clutch.
85 Zuk, 2inch body lift, 2inch spring lift, 2inch exhaust, 31" SIMEX, F100 rims, rollbar, welded rear, racing seat, custom barwork, new paint, rock lights, UHF
Posts: 575
Joined: Sun Mar 13, 2005 9:09 pm
Location: Kingston, Tas

Post by derelict_frog »

Yea but newer cars r a bit quiter than the zook though... :armsup:
Post Reply

Who is online

Users browsing this forum: No registered users and 68 guests