Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Under Bonnet liner

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 1254
Joined: Mon May 16, 2005 8:21 pm
Location: Sth Brissy

Contact:
Contact LuxyBoy

Under Bonnet liner

Post by LuxyBoy »

Mine is disintegrating; Yota want big $ for a new one which will just die again anyway.
I was thinking about ripping it all off and using a spray on type material like under body deadener but with heat resistant properties. I am also adding 1 air vent either side of the bonnet to help heat dissipation.

Any ideas on practicality and what to use?
Anyone done similar?
Kind Regards,
Brad
Top
Posts: 305
Joined: Mon Oct 17, 2005 10:22 am
Location: BRISVEGAS

Contact:
Contact JOHNZ

Re: Under Bonnet liner

Post by JOHNZ »

LuxyBoy wrote:Mine is disintegrating; Yota want big $ for a new one which will just die again anyway.
I was thinking about ripping it all off and using a spray on type material like under body deadener but with heat resistant properties. I am also adding 1 air vent either side of the bonnet to help heat dissipation.

Any ideas on practicality and what to use?
Anyone done similar?
just rip it off.lots of fourbys dont have it. it is primarily for sound proofing
LOVELLS-EFS-DOBINSON-PROCOMP-BILSTEIN-KONI-RANCHO-TOUGHDOG-BLUEMAX
COIL SPACERS from $46pr
4WD SUSPENSION & BODYLIFTS 0418780611 A/H PH/FAX 07 33512692 - www.zordos4wdsuspension.com.au
Top
Posts: 4760
Joined: Mon Dec 30, 2002 6:04 am
Location: Adelaide

Contact:
Contact murcod

Post by murcod »

You can buy self adhesive bonnet liner material from car carpet moulding places.
David
Top
Posts: 86
Joined: Sun Nov 23, 2003 7:21 pm
Location: melbourne

liner

Post by Gibonator »

i ripped my off one day when somthing mechanical didnt go my way hehe.

i thinks its also for catching condensation. but personally get rid of it, i did!
FJ 73, army green ,snorkel, high mount, dual bats,draws,
Top
Posts: 8556
Joined: Mon Jun 13, 2005 9:34 pm
Location: Sydney

Post by RockyF75 »

Under bonnet liner? Whats that? :D
Have had 3 cars + 1 4x4. Never seen bonnet liner :?
60 + Turbo, 33"s :armsup:
Top
Posts: 575
Joined: Sun Mar 13, 2005 9:09 pm
Location: Kingston, Tas

Post by derelict_frog »

Maybe on really hot engines/new cars it stops the shiny paint melting?

So u would want one in that situation.
Top
Posts: 3614
Joined: Sat Nov 02, 2002 9:02 am
Location: Gold Coast

Post by 83 lux »

dont worry about it just throw it away and dont replace it

It will be fine i have not ran one for 2 years
engine bay is cool too. ;)
HOOLAY Wish i could buy boggers for my DH bike
Top
Posts: 217
Joined: Thu Oct 06, 2005 7:52 pm
Location: CABOOLTURE

Re: Under Bonnet liner

Post by pootrol »

I am also adding 1 air vent either side of the bonnet to help heat dissipation.

does your engine get hot enough to warrant the vents.a copetition dude once said to me he thinks its not a good idea to have holes in the bonnet.the reason is when doing water crossings etc the engine bay wont fill up as fast if it can pocket the air in there.bit like pushing a up side down glass into the sink.i dare say it would work alot better if the bonnet had a rubber seal all around.just something that made me think twice.its probably clutching at straws but i could see where he was coming from.
Top
Posts: 1254
Joined: Mon May 16, 2005 8:21 pm
Location: Sth Brissy

Contact:
Contact LuxyBoy

liner

Post by LuxyBoy »

Yeah already thought of that Pootrol. But it is diesel and when the snorkel is fitted it won't bother me :D
Kind Regards,
Brad
Top
Posts: 1606
Joined: Sat Oct 26, 2002 7:20 pm
Location: Geelong

Contact:
Contact HSV Rangie

Post by HSV Rangie »

http://www.tru-fitcarpets.com.au/


MIchael.
Mitsubishi 2010 NT DID Pajero wagon, Factory rear diff lock, Dual batteries, ARB bar, winch, Mt ATZ 4 rib tyres.
1986 RR.
Custom suspension links etc.
HSV 215 engine.
4.3 diffs.
Top
Posts: 238
Joined: Wed Apr 27, 2005 12:11 am
Location: Oz

Post by senergy »

i set fire to mine with an oxy torch while doing some under bonnet welding... I thought it would have been flame retardant but its not.
Top
Posts: 114
Joined: Wed Oct 12, 2005 7:34 pm

..

Post by pilot »

rip it off
Top
Posts: 121
Joined: Sun Jul 18, 2004 12:38 am
Location: Melbourne

Post by Da Zook »

i think that knox auto carpets sell it for relitevly cheap
Top
Posts: 693
Joined: Sun Sep 26, 2004 2:37 pm
Location: Rochedale South - Brisbane

Post by benhl »

Off wid it!

I had one on a past 4b and it got wet and sagged down onto engine parts so ripped it off and found rust starting under there. Better gooonne.

Noticed no difference except there was no where for sand and water to get trapped close to metal. My 2c
GU 4.2 TD Garrett BB Hi-flow, M8274 + Bells & Whistles with plenty of fruit still on the list!
[b][color=red]\ m / ( > . < ) \ m /[/color][/b]
Top
Posts: 136
Joined: Sat Sep 04, 2004 9:40 am
Location: Wellington, NZ

Post by legsx1 »

vents in the bonnet also let steam out when doing river crossings and block your driving view - its not fun not seeing where you got to go
worthog who likes to play in the mud, just follow me, if you can
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 9 guests