Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
5 Speed into a HJ47...
Moderators: toaddog, Elmo, DUDELUX
5 Speed into a HJ47...
I have a 1984 HJ47 that is screaming out for another gear.
How hard is it to put a 5 speed out of say a 60 series in it? Will it just bolt up?
Thanks in advance for your assistance.
How hard is it to put a 5 speed out of say a 60 series in it? Will it just bolt up?
Thanks in advance for your assistance.
have helped do this conversion before using a hj75 gearbox it is a tight fit because of the piece of pipe that braces the chassis at the rear of the gearbox. We had to take the rear transfer case cover off to get it in but if you loosened the engine mounts and some jacking off the motor it should fit. You will need to use your bell-housing there is some difference in the bellhousings i cant remember what. And also new tailshafts front and rear or shorten the rear and put a spacer in the front. Also gearboxes from 2f 3f will fit they are the same box just make sure the input shaft has a coarse spline. The 47 crossmember lines up aswell so the only cutting involved is a little bit to the floorpan to get the shifters to fit from memory we bent the transfer to fit into the stock hole and trimmed the main shifter hole and used a 75 boot to cover the hole.
If at first you dont succeed.......get a bigger HAMMER!!!
I put a 5 spd from a 60 series into my HJ47 troopy - went in no worries, bolted to bell housing good, i think the shafts were different length, didn't measure them as i pulled them from another truck.
I ended up using the floor pan shifter hole cover from the 60 series, and cut/shut/welded to suit my floor. Works great.
I ended up using the floor pan shifter hole cover from the 60 series, and cut/shut/welded to suit my floor. Works great.
Landcruiser UTE 1996 FZJ75 - SPOA, 35"s,
extended chassis, poor mans extra cab, 4.56 diff gears, Lockright front, chinese air locker rear...
extended chassis, poor mans extra cab, 4.56 diff gears, Lockright front, chinese air locker rear...
Mate, the extra gear is not really worth the bother, as the 15% overdrive comes at a cost of reliability, you cant tow in 5th and expect the box to last...also it is only 500 rpm we r talking about at 100 km/hr, so it would be cheaper to look for transfer gears and get a lower low range whilst at it.....you cant blow that 4 speed up if u try
Andrew
Andrew
Got 40 series power steer from a BJ42, used steering box from that, 60 series pump bolted straight to 2H, bend and mod lines to suit, had a new pressure line made up, and also made a bracket to hold the remote reservoir for the p/s steer fluid.
Need more info let me know.
There was also a good thread a while back about this - myself and some others posted pics too.
Cheers
Need more info let me know.
There was also a good thread a while back about this - myself and some others posted pics too.
Cheers
Landcruiser UTE 1996 FZJ75 - SPOA, 35"s,
extended chassis, poor mans extra cab, 4.56 diff gears, Lockright front, chinese air locker rear...
extended chassis, poor mans extra cab, 4.56 diff gears, Lockright front, chinese air locker rear...
Who is online
Users browsing this forum: No registered users and 16 guests