Guys I put a detroit locker in the back of a Series 3 Stage 1 and I was wondering if anyone had done this without changing the axles? I was considering Maxis or Jack Mack but Over the years I have never seen a broken Salisbury Axle. Do I need to change these I only run the original size tyres?
Thanks
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Advice on Salisbury Axles
Moderator: Micka
I know people who have fitted detroits to a salisbury with stock axles without problems.
I managed to break a non-genuine axle in my salisbury on 32's when it was unlocked - if you have genuine axles you should be fine though.
I managed to break a non-genuine axle in my salisbury on 32's when it was unlocked - if you have genuine axles you should be fine though.
_____________________________________________________________
RUFF wrote:Beally STFU Your becoming a real PITA.
I've heard of a couple of NPWS crew cabs breaking them, but how were they driven ??
The only reason we swap them out in Defenders is 'cause the bloody axle splines are dry from the factory and they wear out. Convert to oil lubed axles (like in your Stage 1 or a 110) and no more problems (after fitting Maxi axles)
The only reason we swap them out in Defenders is 'cause the bloody axle splines are dry from the factory and they wear out. Convert to oil lubed axles (like in your Stage 1 or a 110) and no more problems (after fitting Maxi axles)
300Tdi Defender 130 CC
I bought mine from Locked Drive Systems in Sydney it cost me $903 to the door http://www.locked-drive.com.au/
The performance increase in the leaf sprung stage 1 is fantastic you will need to get use to a few creaks and crunches and accept that it will add more driveline backlash to something that already has too much. I have been told that the army are removing thier ARB lockers and replacing them with Detroit Lockers.
The performance increase in the leaf sprung stage 1 is fantastic you will need to get use to a few creaks and crunches and accept that it will add more driveline backlash to something that already has too much. I have been told that the army are removing thier ARB lockers and replacing them with Detroit Lockers.
Ithought the army had detroits alreay not arb's, More backlash? a detroit should of helped to reduce it, who set your diff up?djam1 wrote:I bought mine from Locked Drive Systems in Sydney it cost me $903 to the door http://www.locked-drive.com.au/
The performance increase in the leaf sprung stage 1 is fantastic you will need to get use to a few creaks and crunches and accept that it will add more driveline backlash to something that already has too much. I have been told that the army are removing thier ARB lockers and replacing them with Detroit Lockers.
Wanted: Car trailer or beaver tail truck, let me know what you got
Cloughy
The diff setup has nothing to do with the backlash in the detroit mechanism
To quote the detroit manual
"Backlash or slack between the driving and driven clutch teeith is an inherent part of the Detroit Locker and necessary to permit automatic operation when driving in forward and recerse. The total backlash in the driveline is increased by the amount of the reduction between the ring gear and pinion. If the ring gear to pinion ratio is 5 to 1 the total backlash in the driveline with a Detroit Locker would be about 30 degrees. This in turn is increased by the clearances between planetary gear, sliding splines and ring and pinion gear. We feel that the total driveline slack can amount to as much as 1/4 of a turn of the driveline without being abnormal." Combine this with the backlash in an LT95 and it takes some getting use to.
The diff setup has nothing to do with the backlash in the detroit mechanism
To quote the detroit manual
"Backlash or slack between the driving and driven clutch teeith is an inherent part of the Detroit Locker and necessary to permit automatic operation when driving in forward and recerse. The total backlash in the driveline is increased by the amount of the reduction between the ring gear and pinion. If the ring gear to pinion ratio is 5 to 1 the total backlash in the driveline with a Detroit Locker would be about 30 degrees. This in turn is increased by the clearances between planetary gear, sliding splines and ring and pinion gear. We feel that the total driveline slack can amount to as much as 1/4 of a turn of the driveline without being abnormal." Combine this with the backlash in an LT95 and it takes some getting use to.
Was asking who set it up because EXCESSIVE backlash will usually be caused from incorrect crownwheel to pinion contact or worn cross pin and or thrust washers in the centre, obviously you don't have the later. ifully understand the ramping effect needed for locking a detroit but i've driven on a few and never found them to be worse than a 20 year old centre, only better for backlashdjam1 wrote:Cloughy
The diff setup has nothing to do with the backlash in the detroit mechanism
To quote the detroit manual
"Backlash or slack between the driving and driven clutch teeith is an inherent part of the Detroit Locker and necessary to permit automatic operation when driving in forward and recerse. The total backlash in the driveline is increased by the amount of the reduction between the ring gear and pinion. If the ring gear to pinion ratio is 5 to 1 the total backlash in the driveline with a Detroit Locker would be about 30 degrees. This in turn is increased by the clearances between planetary gear, sliding splines and ring and pinion gear. We feel that the total driveline slack can amount to as much as 1/4 of a turn of the driveline without being abnormal." Combine this with the backlash in an LT95 and it takes some getting use to.
Wanted: Car trailer or beaver tail truck, let me know what you got
Who is online
Users browsing this forum: No registered users and 37 guests