Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Axle splines question

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 1404
Joined: Tue Jan 07, 2003 9:20 pm
Location: Sitting on Miss Janes lap.

Axle splines question

Post by Drafty »

Are the splines on a GQ axle and a GU axle the same at the diff end? :?

1 out of a 4.2L GQ Diesel and the other out of a 4.5L GU petrol.
Joe.


To succeed, focus on the solution, not the problem.
Top
Posts: 2492
Joined: Sun Nov 24, 2002 8:57 pm
Location: Melbourne

Post by bazzle »

Yes

http://www.arb.com.au/

All the info here under lockers


Bazzle
Top
Posts: 1404
Joined: Tue Jan 07, 2003 9:20 pm
Location: Sitting on Miss Janes lap.

Post by Drafty »

Thanks Bazzle. :D
Joe.


To succeed, focus on the solution, not the problem.
Top
Posts: 3443
Joined: Tue Oct 29, 2002 10:50 pm
Location: Currently On the Road !!

Post by Dozoor »

Depends on what your doing drafty ,The splines are the same but the length on the rears are different , only know from seeing the end product of running a gq axle in the rear of a gu at TT, theres about ten mm diference so the spline on the gq only penatrates half way when placed in a gu housing ! This is correct Nissan dudes ? If so then a gu axle in a gq would not seat at the bearing end aswell. :cry:
Larry.
Top
Posts: 16934
Joined: Sun Oct 20, 2002 6:57 pm

Post by RUFF »

Yeah i remember this happening at TTC as well. Was it Menal motors?
Top
Posts: 3443
Joined: Tue Oct 29, 2002 10:50 pm
Location: Currently On the Road !!

Post by Dozoor »

I think it was ruff, certianly chewed the end of that axle ha.
Larry
Top
Posts: 3924
Joined: Mon Oct 21, 2002 10:35 pm
Location: Newcastle NSW

Contact:
Contact hypo

Post by hypo »

yeah it was Nick Mannell's BIG GU. altho i didnt know that it was running a GQ axle in the rear i thought it was a GU :?: :?:
:finger: HYPOFAB :finger:

Thanks to:

Polyperformance
Yuri 4x4
Longfield
Top
Posts: 3443
Joined: Tue Oct 29, 2002 10:50 pm
Location: Currently On the Road !!

Post by Dozoor »

hypo he aparantly put a gq axle in by mistake , and there a tad shorter.
Top
Posts: 1404
Joined: Tue Jan 07, 2003 9:20 pm
Location: Sitting on Miss Janes lap.

Post by Drafty »

We are going to put my GU front diff in the front of the GQ we are building but want to use the GQ centre with locker from our old GQ. Every component will be GU except the centre and locker setup.
Joe.


To succeed, focus on the solution, not the problem.
Top
Posts: 4065
Joined: Thu Oct 24, 2002 8:31 am
Location: ACT

Contact:
Contact Wendle

Post by Wendle »

Dozoor wrote:hypo he aparantly put a gq axle in by mistake , and there a tad shorter.


12.5mm - don't get enough spline engagement. If you get it wrong the other way (gu axle into gq housing) you are left doing this :crazyeyes: as the axle won't slide in enough.
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 0 guests