Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Chopped!
Moderator: Micka
LOL, thanks man - with the underdrive, 4.88s, and ZF, I'm looking forward to some sweet crawling...
Just got my hands on a huge hydro signaw pump, and that'll be all she wrote for the drivetrain!
Just need to stabilize the cabin on the chassis and run the exo
Just got my hands on a huge hydro signaw pump, and that'll be all she wrote for the drivetrain!
Just need to stabilize the cabin on the chassis and run the exo
LR Disco truggy:
42" Iroks, ZF, dual cases & ARBs, 30 splined, Longfielded, OMEs, Optimas, M8274-50s, Rockstomper rope & Bead-L
LR D-90 TD5 ST:
33" BFT AT, tuned, caged, 1/2 top
42" Iroks, ZF, dual cases & ARBs, 30 splined, Longfielded, OMEs, Optimas, M8274-50s, Rockstomper rope & Bead-L
LR D-90 TD5 ST:
33" BFT AT, tuned, caged, 1/2 top
zf auto
g"day disco dino nice job . I run a 4.6 in my defender with a zf 4hp22 bought it already rebuilt, it lasted 20,000 in 1 year (was giving it a bit of a work out ) about 18,000 was off road .I destroyed the planetary gears the rest of the box was fine so I rebuilt it again this time using bmwv12 planetary gears drilled out the oil wells to allow maximum oil flow and a 30% lower first gear. Done about 3,000k so far couldn't be happier I driven in soft sand sitting on about 3-4000rpm for about half hour at about 40-50km/h and the hottest temp reading i got was 80deg Celcius the oil cooler I run is only 100mm high x 400mm wide x 15mm thick so as you can tell its not very large at all its mounted at the front of the car with twin thermo's in front of in (the only place i could fit them) hope this info is helpful and can't wait to see the finished product Cheers hally 
defender 110,4.6,auto,36simex,maxidrive everything. "JEEP" your right, I dont understand????
Some recent updates
Main outer Exo tubing (expensive CDOM 60mm x 4mm)
Final approach angle:
Clearance under the belly is 63cm
Main rock slider / cab mount:
Nice and wide - front end fully clearanced for tires and engine/tranny oil coolers:
Same, different angle:
Winch basket mock up - tubing to start from the top tip of the basket (made out of 8mm single piece bent and rewelded!)L
Rear winch basket set-up (will be 2-3" higher up):
Width, exo safety clearnace and body:
Main outer Exo tubing (expensive CDOM 60mm x 4mm)
Final approach angle:
Clearance under the belly is 63cm
Main rock slider / cab mount:
Nice and wide - front end fully clearanced for tires and engine/tranny oil coolers:
Same, different angle:
Winch basket mock up - tubing to start from the top tip of the basket (made out of 8mm single piece bent and rewelded!)L
Rear winch basket set-up (will be 2-3" higher up):
Width, exo safety clearnace and body:
LR Disco truggy:
42" Iroks, ZF, dual cases & ARBs, 30 splined, Longfielded, OMEs, Optimas, M8274-50s, Rockstomper rope & Bead-L
LR D-90 TD5 ST:
33" BFT AT, tuned, caged, 1/2 top
42" Iroks, ZF, dual cases & ARBs, 30 splined, Longfielded, OMEs, Optimas, M8274-50s, Rockstomper rope & Bead-L
LR D-90 TD5 ST:
33" BFT AT, tuned, caged, 1/2 top
Loanrangie wrote:Not so much as bad but as in using whatever is close by to do the jobDiscoDino wrote:Excuse me? Booty fab? you mean BAD fabrication?
hell yeah, but I'm importing anything that I may be of need (heims + their stuff, switches, lights...even the damn under-drive 
)...I do guarantee that the quality is real good, not "baja welders show truck" style, but functional for sure!
Thought you were insinuating that it was a patch-up job! both my heart and wallet went south
!LR Disco truggy:
42" Iroks, ZF, dual cases & ARBs, 30 splined, Longfielded, OMEs, Optimas, M8274-50s, Rockstomper rope & Bead-L
LR D-90 TD5 ST:
33" BFT AT, tuned, caged, 1/2 top
42" Iroks, ZF, dual cases & ARBs, 30 splined, Longfielded, OMEs, Optimas, M8274-50s, Rockstomper rope & Bead-L
LR D-90 TD5 ST:
33" BFT AT, tuned, caged, 1/2 top
Hey Dino .. I haven't read all the previous thread (too lazy 
) are you gonna put a rear window in that rear panel?
I might say the rig looks fabulous ... love your work. But where do you get the time to do all that work?" ... you must be single with no kids or have a very understanding family
Simo
) are you gonna put a rear window in that rear panel?I might say the rig looks fabulous ... love your work. But where do you get the time to do all that work?" ... you must be single with no kids or have a very understanding family
Simo
TD 80 Series, F&R Lockers, Winch etc
Who is online
Users browsing this forum: No registered users and 0 guests