Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

SMOKE'N!!!

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Post Reply
Posts: 660
Joined: Sat Jul 30, 2005 5:43 pm
Location: No fixed address....

SMOKE'N!!!

Post by GU BUG »

I have a 99 4.2 turbo diesel GU & have a couple of issues with it at the moment :?. It seems whenever I start it up cold in the morning (or in the day for that matter) it blows a lot of diesel smoke. I know a lot of them do but mine seems to blow more than most :?. Also, it's reasonabley heavy on the juice too. This summer I had a problem with it heating up a couple of times & it used to want to run on when I turned it off if it was cold :? (though it hasn't done this for a while). Also, some days it seems to run a lot better than others & will pull hard. Others, it runs like a slug. Any ideas :armsup:???

Cheers
Joe
Last edited by GU BUG on Mon Jun 19, 2006 8:47 pm, edited 1 time in total.
More poke = More smoke!!!
Posts: 533
Joined: Sat Jan 15, 2005 4:54 pm
Location: Melbourne, Australia.

Post by InSanE »

sounds like you could have a few dribbling injectors that would cause the black smoke at startup, if its white it will be a glowplug but from what u said it sounds like u need your injectors done.
GQ LWB TD42, boost, lockers etc

http://forum.mudrhino.com.au/viewtopic.php?t=262&start=30
Posts: 660
Joined: Sat Jul 30, 2005 5:43 pm
Location: No fixed address....

Post by GU BUG »

I had new injectors put in 30,000k's ago :?.
More poke = More smoke!!!
Posts: 533
Joined: Sat Jan 15, 2005 4:54 pm
Location: Melbourne, Australia.

Post by InSanE »

maybe check the valve clearances? if they are out it can cause your truck to run on and lack a bit of power
GQ LWB TD42, boost, lockers etc

http://forum.mudrhino.com.au/viewtopic.php?t=262&start=30
Posts: 660
Joined: Sat Jul 30, 2005 5:43 pm
Location: No fixed address....

Post by GU BUG »

InSanE wrote:maybe check the valve clearances? if they are out it can cause your truck to run on and lack a bit of power
They too were adjusted when I got my injectors done :D. I'm thinking maybe the injector pump could have something to do with it :?.....
More poke = More smoke!!!
Posts: 45681
Joined: Wed Nov 27, 2002 10:13 am

Post by bogged »

GU BUG wrote:
InSanE wrote:maybe check the valve clearances? if they are out it can cause your truck to run on and lack a bit of power
They too were adjusted when I got my injectors done :D. I'm thinking maybe the injector pump could have something to do with it :?.....
Have you called who ever did the job on the injectors etc etc ?? What did they say?
Posts: 625
Joined: Fri Feb 20, 2004 12:04 am
Location: Melbourne

Post by Woop »

When adjusting tappets, its very easy to adjust them too tight. This is due to the timing marks on the front pulley being hard to see and line up exactly with the pointer. Check your tappets again--preferably with a dial gauge to get TDC point correct then check tappets again. I have had problems with re-con Injectors not having the crack pressure set properly before. It COULD be a worn pump though........ Has any-one fiddled with the pump timing before?

Nick
Posts: 660
Joined: Sat Jul 30, 2005 5:43 pm
Location: No fixed address....

Post by GU BUG »

bogged wrote:
GU BUG wrote:
InSanE wrote:maybe check the valve clearances? if they are out it can cause your truck to run on and lack a bit of power
They too were adjusted when I got my injectors done :D. I'm thinking maybe the injector pump could have something to do with it :?.....
Have you called who ever did the job on the injectors etc etc ?? What did they say?
I'll call past his shop tomorrow & see what he has to say....
More poke = More smoke!!!
Posts: 660
Joined: Sat Jul 30, 2005 5:43 pm
Location: No fixed address....

Post by GU BUG »

Woop wrote:When adjusting tappets, its very easy to adjust them too tight. This is due to the timing marks on the front pulley being hard to see and line up exactly with the pointer. Check your tappets again--preferably with a dial gauge to get TDC point correct then check tappets again. I have had problems with re-con Injectors not having the crack pressure set properly before. It COULD be a worn pump though........ Has any-one fiddled with the pump timing before?

Nick

Since I've had it, nobody has played with the pump at all & I'm guessing it's probably never been touched before hand :?. I purchased it with just under 200,000 & the injectors hadn't been changed either :roll:.
More poke = More smoke!!!
Posts: 625
Joined: Fri Feb 20, 2004 12:04 am
Location: Melbourne

Post by Woop »

Sounds like you probably need to get injectors checked. B.J Diesel Injection Service-- Greens Rd Dandenong do a very good job, but might be a bit of a drive for you though.

Nick
Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests