Hey hey,
Have a little obscure problem here. I bought a semi-complete turbo kit a while back now and have had it fitted to my car for some time (TD42). It is a turbo glide hi-mount kit and it's going quite well..
That aside when I first got it I was missing the high pressure "t" fitting that screws into the side of the block. This T fitting is responsible for feeding both the turbo and the vaccuum pump on the alternator with oil. As it was missing I went to a pneumatic/air/gasweld sort of place and got a t-piece that 'sort' of did the job, but the threads are a bit big, so the mechanic who fitted it used thread tape....
It has started to leak from this particular point now and I figure I should probably go and get a t fitting with the correct threads for when I do my next grease and oil ? Question is where in the bloody hell do I get one with the correct threads ? Someone on here would know... they are a common part for all td42's fitted with aftermarket turbos and as such most probably would all be the same size thread ? So where do I go and what do I ask for ?
Thanks for listening to my mindless ramblings...
Jeremy
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Turbo Oil Line Fittings....
Turbo Oil Line Fittings....
Last edited by JemmyBubbles on Wed Jun 28, 2006 1:14 pm, edited 2 times in total.
[quote="MSCHIF"]SPUA its like shaving a barbie dolls head, amusing but pointless.[/quote]
...
Thanks guys sooo much......
nub question does VDO have a website... did a search couldn't find much.
Spanner Cab what part would I be asking for If I were to buy one of these from VDO... ??
nub question does VDO have a website... did a search couldn't find much.
Spanner Cab what part would I be asking for If I were to buy one of these from VDO... ??
[quote="MSCHIF"]SPUA its like shaving a barbie dolls head, amusing but pointless.[/quote]
When i fitted my turbo (Safari) i used a tee that i sourced from Pirtek. They seemed to have a good range of fittings there. Cost was about $30.
Just take all your fittings along, so they can know what you need. The fitting into the block is something weird.
From memory, i have an adaptor that screws into the block, then the tee piece. The turbo oil feed screws in one side, the vacuum oil feed in the other with another adaptor.
In future, i'll probably get a new line made up for the vacuum pump out of braided line like the turbo oil feed with a fitting to suit the tee, as it takes up a bit of room with all the adaptors.
Apparantly there is another oil gallery near the engine mount you can tap into as well. Not 100% sure on this one though.
Hope this helps.
Nathan
Just take all your fittings along, so they can know what you need. The fitting into the block is something weird.
From memory, i have an adaptor that screws into the block, then the tee piece. The turbo oil feed screws in one side, the vacuum oil feed in the other with another adaptor.
In future, i'll probably get a new line made up for the vacuum pump out of braided line like the turbo oil feed with a fitting to suit the tee, as it takes up a bit of room with all the adaptors.
Apparantly there is another oil gallery near the engine mount you can tap into as well. Not 100% sure on this one though.
Hope this helps.
Nathan
Who is online
Users browsing this forum: No registered users and 111 guests