lost the b.b

Post by **ronoor** » Wed Aug 30, 2006 8:25 pm

lost the ball bearing for the 4wd switch out of the transfer any ideas ? what size is it . cheers ron

Post by **RB zook** » Wed Aug 30, 2006 8:39 pm

what transfer

Post by **ronoor** » Wed Aug 30, 2006 8:45 pm

91 sierra pulled the transfer case out to fit gears was cleaning it on the front lawn . lost

Post by **Spike_Sierra** » Wed Aug 30, 2006 9:10 pm

i got one, will post it to you in the mail if you like, will have to make sure i have the ball bearing still.
pm me your address

Post by **Bad JuJu** » Wed Aug 30, 2006 9:13 pm

Measure the hole it drops in .... Its about 8mm I think, use an allan key for sizing.

Post by **Aerenandmel** » Wed Aug 30, 2006 9:19 pm

Bad JuJu wrote:Measure the hole it drops in .... Its about 8mm I think, use an allan key for sizing.

or a drill bit

Post by **droopypete** » Wed Aug 30, 2006 11:02 pm

Even easier, get a magnet and pass it over your lawn where you cleaned it

Peter.

Post by **Bad JuJu** » Wed Aug 30, 2006 11:40 pm

Take the case to the baring shop and see what fits in the hole. BTW there is two more BB in there too, all the same size by the looks of it.

Or leave the center one out and have 2-low capability (but a funky shift pattern)

Post by **suzuki boy** » Thu Aug 31, 2006 4:50 pm

What gears did you end up going with?

Post by **ronoor** » Thu Aug 31, 2006 6:55 pm

gearmaster with the 31'' tyres 100k 5gear just over 3000 rpm low range is unreal . stuff i use to do in 1st now 3rd /4. cheers ron

Post by **suzuki boy** » Fri Sep 01, 2006 7:04 pm

They from marks? How much did they set you back if you don't mind me asking? Thanks

Post by **Spike_Sierra** » Fri Sep 01, 2006 9:39 pm

just put her in the mail so expect it sometime next week

Post by **ronoor** » Fri Sep 01, 2006 10:07 pm

thanks mate your a champ. spent two days on the lawn with a magnet neighbours thought i was going crazy .still cant find so once again thanks .cheers ron

Post by **ronoor** » Tue Sep 05, 2006 3:41 pm

got your mail today' bloody aust post someone had opened it its gone i,ll have to go to a bearing place try a few size's cheers ron

Post by **Spike_Sierra** » Tue Sep 05, 2006 6:38 pm

bloody thought that would happen, sorry champ, i tried

Post by **ronoor** » Tue Sep 05, 2006 8:04 pm

I'll try a bearing place tomorrow .cheers

Post by **ronoor** » Wed Sep 06, 2006 1:55 pm

tried 3 sizes today 8mm no go' 9mm no go starting to panic;10mm did the job. cheers ron

Post by **ronoor** » Wed Sep 06, 2006 2:35 pm

I tell a lie tightened it up light stays on tried 9mm dont work so 9.5mm is the go is that3/8

cheers ron

Post by **bazooked** » Wed Sep 06, 2006 3:15 pm

3/8 is close to 9.5mm but being a jap box i thought it would have been metric?

Post by **ronoor** » Wed Sep 06, 2006 4:52 pm

All the screwing and unscrewing broke the wire at the base .cut it back with side cutters resolded drop in 3/8 or 9.5 now it works .moral to this story dont loose the B.B.cheers ron

Outer Limits 4x4 Board

lost the b.b

lost the b.b

Who is online