This little tooth got chipped.... and then went on a magical mystery tour, floating about in the transfer case wreaking havoc on the other gears 
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Carnage
Moderator: Tiny
God Of Emo
Posts: 7350
Joined: Sun Aug 24, 2003 7:04 pm
Joined: Sun Aug 24, 2003 7:04 pm
Location: Newy, home of the ZOOK (Rockin the 'diff)
Contact:
Looks like my old S1 rock hoppers, except nowhere near as bad. Was the chip caused by fatigue on the teeth, or did a bearing fail, allowing the teeth to get misaligned??
Layto....
Layto....
[quote="v840"]Just between me and you, I actually really dig the Megatwon, but if anyone asks, I'm going to shitcan it as much as possible! :D[/quote]
I was doing bunny hops 
... 'dragging' a tractor, mucking around and then started making a grinding noise (first tooth that went).... kept driving then about 50k's later heard an almighty BANG, that was the 'bit' of the tooth going through the rest of the gears 
... the grinding noise then bacame this constant rolling clunking noise and I limped it to the mech the next day.... had a que of traffic a km or so long behind me cause I didn't dare go over 40k/hr 
I can't believe that broke it Must ave been worn already, i've given it more offroad, it was just like quick tapping the gas and then lettin it off , like L platers do cause they dunno how to use a clutch 
... 'dragging' a tractor, mucking around and then started making a grinding noise (first tooth that went).... kept driving then about 50k's later heard an almighty BANG, that was the 'bit' of the tooth going through the rest of the gears ... the grinding noise then bacame this constant rolling clunking noise and I limped it to the mech the next day.... had a que of traffic a km or so long behind me cause I didn't dare go over 40k/hr I can't believe that broke it
Must ave been worn already, i've given it more offroad, it was just like quick tapping the gas and then lettin it off , like L platers do cause they dunno how to use a clutch 60 + Turbo, 33"s :armsup:
Ooch. That does look a bit painful. I remember those gears.
I'm just wondering why you would want to make out to look like you can't drive?
Drive line backlash can do serious damage... as you have proved. The more backlash there is the more chance of damage. I think the diff and tail shaft are pretty criticle here. If there both tight, then it tends to limit the amount of free play in the gearbox and transfer, hence reducing backlash.
Mine seems to have a bit but it hasn't caused a problem... cos I can drive...
Good luck with the repair. Hope it doesn't hurt the bank too much.
Let us know of the final cost. It'd be good to know how much those gears are each as well.... just incase.
Cheers.
I'm just wondering why you would want to make out to look like you can't drive?
Drive line backlash can do serious damage... as you have proved. The more backlash there is the more chance of damage. I think the diff and tail shaft are pretty criticle here. If there both tight, then it tends to limit the amount of free play in the gearbox and transfer, hence reducing backlash.
Mine seems to have a bit but it hasn't caused a problem... cos I can drive...
Good luck with the repair. Hope it doesn't hurt the bank too much.
Let us know of the final cost. It'd be good to know how much those gears are each as well.... just incase.
Cheers.
If it doesn't have two sticks, I don't wana know about it!
This quite often happens due to shock loading.
ie a spinning wheel suddenly coming into contact with the ground and the drive train suddenly being loadeed up again. Puts enourmous (sp?) amounts of load on the gearing.
i have done exactly this and busted the front diff immediatly and the gearbox layshaft went the following week. $190 (2nd hand diff) replaced my self. $900 (grb) to be repaired, thats with me removing the gearbox.
Sounds like what would happen with 'bunny hops' ....shock loading
either way mate it's bad luck but at least ya got some good 'trophies' now hehehe
ie a spinning wheel suddenly coming into contact with the ground and the drive train suddenly being loadeed up again. Puts enourmous (sp?) amounts of load on the gearing.
i have done exactly this and busted the front diff immediatly and the gearbox layshaft went the following week. $190 (2nd hand diff) replaced my self. $900 (grb) to be repaired, thats with me removing the gearbox.
Sounds like what would happen with 'bunny hops' ....shock loading
either way mate it's bad luck but at least ya got some good 'trophies' now hehehe
Clint,
Limited Edition 95 Roza & 2006 ST Patrol Coil Cab Ute.... both a work in progress.
Limited Edition 95 Roza & 2006 ST Patrol Coil Cab Ute.... both a work in progress.
God Of Emo
Posts: 7350
Joined: Sun Aug 24, 2003 7:04 pm
Joined: Sun Aug 24, 2003 7:04 pm
Location: Newy, home of the ZOOK (Rockin the 'diff)
Contact:
Funny you say that, thats where my old rock hoppers currently reside, as paper weights on my desktabrocky wrote:I was actually thinking "paper weight" too...Clint wrote: either way mate it's bad luck but at least ya got some good 'trophies' now hehehe
Cheers.
Layto....
[quote="v840"]Just between me and you, I actually really dig the Megatwon, but if anyone asks, I'm going to shitcan it as much as possible! :D[/quote]
1st Q - With mates, muddy car, country music turned up, 'dragging' a tractor off at the lights...whilst bunny-hopping....you had to be theretabrocky wrote: I'm just wondering why you would want to make out to look like you can't drive?
.......
Good luck with the repair. Hope it doesn't hurt the bank too much.
Let us know of the final cost. It'd be good to know how much those gears are each as well.... just incase.
Cheers.
It was funny at the time Final cost was $880, but second hand gears. Guestimated cost of GEARS ALONE if new was around $1200-$1500, plus the possible wait to get them in.
60 + Turbo, 33"s :armsup:
What can I say RockyF70... You're a trend-setter. God damn it!!
Got in the car to go to a barby the other wkend for the grand final. Hmm whats that unusual noise eminating from underneath? Doesn't sound good.
Turned around and went home... got a lift with a mate instead.
Decided not to risk possible further damage so I trailered it 100ks to my folks place (where all my tools are) and had a bit of a look to see what was exactly going on.
After running the gearbox with the T-case in neutral, the noise wasn't present, so it meant it had to be some where on the output side in the T-case. Removing the tailshaft revealed a notchy feel when the output shaft was turned by hand.... Collapsed bearing.
I drained the T-case oil and found it to have a similar look to graphite grease (lots of tiny silver glitter in it) I decided that there was definatley a problem!!!
Here's what I found...
http://www.putfile.com/pic.php?img=3595813
See anything wrong with that bearing??
http://www.putfile.com/pic.php?img=3595814
And the T-case removed
I rebuilt everything about 100,000k ago with no problems since, BUT there was one bearing I couldn't get off.
Guess which bearing it was...
Should have known. Ahh well my own fault I guess.
Cost to repair i'm guessing will be around $100 all up. Could have been a lot more, had I kept driving it.
Cheers.
Got in the car to go to a barby the other wkend for the grand final. Hmm whats that unusual noise eminating from underneath? Doesn't sound good.
Turned around and went home... got a lift with a mate instead.
Decided not to risk possible further damage so I trailered it 100ks to my folks place (where all my tools are) and had a bit of a look to see what was exactly going on.
After running the gearbox with the T-case in neutral, the noise wasn't present, so it meant it had to be some where on the output side in the T-case. Removing the tailshaft revealed a notchy feel when the output shaft was turned by hand.... Collapsed bearing.
I drained the T-case oil and found it to have a similar look to graphite grease (lots of tiny silver glitter in it) I decided that there was definatley a problem!!!
Here's what I found...
http://www.putfile.com/pic.php?img=3595813
See anything wrong with that bearing??
http://www.putfile.com/pic.php?img=3595814
And the T-case removed
I rebuilt everything about 100,000k ago with no problems since, BUT there was one bearing I couldn't get off.
Guess which bearing it was...
Should have known. Ahh well my own fault I guess.
Cost to repair i'm guessing will be around $100 all up. Could have been a lot more, had I kept driving it.
Cheers.
If it doesn't have two sticks, I don't wana know about it!
Who is online
Users browsing this forum: No registered users and 4 guests