Are Bump Stops Necessary?

Website · Post by **LuxyBoy** » Wed Nov 01, 2006 7:56 pm

91' Hilux lost one the other day when one of my new u-bolts came off

I no longer take advise from this board about not using my breaker bar to do them up

So my question is do you need them?

Post by **lay80n** » Wed Nov 01, 2006 8:08 pm

I would say yes, otherwise you can possibly stress the shocks but collapsing them on full uptravel and using them as a bumpstop. This is not good for the shock, or the mounts. THe mounts (factory setup) are not designed to take the load that they may endure. Also, if you setup your suspension properly you can gain "forced droop" by making hte axle pivot on the bumpstop.

Layto....

Post by **muppet_man67** » Wed Nov 01, 2006 10:12 pm

and if your really unlucky then your diff may go through your sump.

Post by **Shadow** » Thu Nov 02, 2006 12:26 am

about as necessary as undies

sure its cool to freeball around, but without a safety net your asking for trouble.

Post by **brighty** » Thu Nov 02, 2006 5:05 am

Shadow wrote:about as necessary as undies

sure its cool to freeball around, but without a safety net your asking for trouble.

Well, thats one way to put it huh!!!

Post by **Damo** » Thu Nov 02, 2006 9:35 am

LuxyBoy wrote: I no longer take advise from this board about not using my breaker bar to do them up

So my question is do you need them?

Why bother asking, you're not going to take advise from here anymore anyway

My advise

is not to run no bumpstops

Post by **Ruffy** » Thu Nov 02, 2006 5:02 pm

Ok.. so you've done a homer on your own car, Muffed it, and it's outers fault... I see how!

Are bump stop necessary?.. in short. YES

Manafacturers spend lots of money designing things the cheapest way they can. If they weren't nec' they wouldn't be there. They have a purpose.

Post by **Rangie Thing** » Thu Nov 02, 2006 5:21 pm

I lost a bump stop on my rocky, then i lost the power steering pump as the diff center took that out!!

Post by **of4x4** » Thu Nov 02, 2006 5:27 pm

Ruffy wrote:Manafacturers spend lots of money designing things the cheapest way they can. If they weren't nec' they wouldn't be there. They have a purpose.

Explain why manufacturers put sway bars on so we can take them off......?

I agree with you that the bump stop is necessary. Without it, what else stops the movement when it bottoms out. Diff on what...?

Post by **bazzle** » Wed Nov 08, 2006 12:56 pm

And U bolts dont just come off. They work loose. Sometimes the threads stretch. (breaker bar) It up to you to check, sometimes daily on a cross country run.
You can use a thin locknut if you want too.

Bazzle

Post by **shorty_f0rty** » Wed Nov 08, 2006 4:33 pm

dont ubolts stretch to some degree which is why its recommended by suspension places to check/retighten your ubolts after 500kms when they are replaced?

at least this is what i heard from carrolls springs at wacol..

Post by **badger** » Wed Nov 08, 2006 4:43 pm

if you did them up with a breaker bar they still woulda come loose you wombat. you need locknuts and/or split washers on these components.
using a breaker bar will just streach the bolt and make it come lose or sheer faster.

if you use your 4wd as a 4wd you should regularily check suspension components among other things.

and yes bumpstops are nessesary so that next time u stuff up your u bolts your diff stops going upwards before it destroys your undercarriage and or pannels:P

Post by **Shadow** » Wed Nov 08, 2006 4:49 pm

badger wrote:if you did them up with a breaker bar they still woulda come loose you wombat. you need locknuts and/or split washers on these components.
using a breaker bar will just streach the bolt and make it come lose or sheer faster.

if you use your 4wd as a 4wd you should regularily check suspension components among other things.

and yes bumpstops are nessesary so that next time u stuff up your u bolts your diff stops going upwards before it destroys your undercarriage and or pannels:P

if thge ubolts break the bumb stop isnt gonna stop it, it will just move to the side of the bump stop and smash your sump anyway.

Post by **ofr57** » Wed Nov 08, 2006 6:08 pm

I think you just get some RHS and weld one end to the diff and the other end to the chassie ... no more worry about that diff moving

Website · Post by **LuxyBoy** » Wed Nov 08, 2006 8:18 pm

Well half of you are complete morons who just want to have go at me

To everyone else thankyou for your input

All i said is that i would be using the breaker bar again instead of not using it like i was recommended by someone on here.
U-bolt kits come with split washers so unless you are stupid enough to throw them out you put them on like i did.
I used the 1/2 drive deep drive socket with ratchet and full force and i am not a little fella. The bloody thing still came off

Last time i changed them with breaker bar; i checked after one week and readjusted, this time it fell off in two days

stupid thing.
Have since adjusted it with the breaker bar what do you know it hasn't moved at all

Again thank to all those who did post positive information

and not just give me

Flame suit on

[/RANT]

Post by **Weiner** » Wed Nov 08, 2006 8:32 pm

Why not try some loctite on the bolts and nuts?

Post by **Shadow** » Wed Nov 08, 2006 9:20 pm

or a second nut on each thread. (called a locking nut)

Post by HG » Thu Nov 09, 2006 7:18 am

Locktiite is the go .
Luxyboy whats the car in your avitar --- Mclaren ?

Post by **bazzle** » Fri Nov 10, 2006 3:14 pm

Hilux fronts especially will work loose all the time due to curve on axle seat. 2nd locking nuts is the only way to go. Recheck them on a regular basis.

Bazzle

Outer Limits 4x4 Board

Are Bump Stops Necessary?

Are Bump Stops Necessary?

Re: Are Bump Stops Necessary?

Who is online