Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

T700vsT350 opinions ideas

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Post Reply
Posts: 16
Joined: Wed Nov 27, 2002 9:22 pm

T700vsT350 opinions ideas

Post by 8runner »

hi all im considering putting an auto behind my 253 and im not sure which. any pros cons with the above two and anyone know where i can get a good one in perth also what adaptor suppliers do you recommend cheers shaun
Posts: 1361
Joined: Thu Oct 24, 2002 8:47 pm
Location: Now in a happy place.

Post by Cheezy4x4 »

Im going with a T4oo as the auto joint building my auto ( Kewish auto's) told me they wouldnt give me anything else as I would be back in a week.
As for Adaptors, Ring Marks Adaptors in Melb, tell them Cheezy sent you for a good deal. :D
Posts: 2149
Joined: Sun Oct 20, 2002 6:59 pm
Location: gold coast, australia

Post by NICK »

i think you will find the 700 is too long and not strong enough like mark said, althou it does have a 4sp over drive.


NICK
TECH SCREW GURU
User avatar
cbr
Posts: 644
Joined: Mon Oct 21, 2002 1:14 am
Location: Perth

Re: T700vsT350 opinions ideas

Post by cbr »

8runner wrote:hi all im considering putting an auto behind my 253 and im not sure which. any pros cons with the above two and anyone know where i can get a good one in perth also what adaptor suppliers do you recommend cheers shaun


I had a t350 behind my 253 and then behind my 5.0lt. Did not like it much. Lots of revs, really bad fuel consumption and no engine braking (4.88 ratio's with 35"). So I went with a 5 speed in my current 4runner. This is much better.
If you are set on an auto and it is not a trail only rig then I would go for the t700. I would try get an adapter that uses a 4-speed type transfer case (shifter in the t/case). This will mean the adapter is much shorter, but you will need to change the transfer case you have. You will make sure that the transmission is also beefed up and running a external cooler.

Chris
Posts: 1544
Joined: Tue Oct 22, 2002 8:37 am
Location: Performing booty fab in my Garage

Post by Wooders »

Surely you could fit a t700 in a runner?? I mean in something like a CJ5 it's a bloody tight fit, but it's on about 1½" longer than the t350, o/drive and PLENTY of upgrade options....IMHO it would be a no brainer decision....
Cheers [url=http://www.wooders.com.au]Wooders[/url]
User avatar
cbr
Posts: 644
Joined: Mon Oct 21, 2002 1:14 am
Location: Perth

Post by cbr »

Wooders wrote:Surely you could fit a t700 in a runner?? I mean in something like a CJ5 it's a bloody tight fit, but it's on about 1½" longer than the t350, o/drive and PLENTY of upgrade options....IMHO it would be a no brainer decision....


The reason why I would go for a shorter adapter is so that if you go dual t/cases it wil not be a problem.

Chris.
Posts: 82
Joined: Tue Nov 12, 2002 7:34 pm
Location: workin round the world

Post by wanna »

turbo 350 good how you going to bolt it behind your 253 adpter plate or redrill the block 700 good but bad points are weight length and cost to rebuild i can get a 350 that will handle 400hp for 1000$ a 700 will cost nearly 3 times that for the same hp
Dont be scared give it a go
User avatar
cbr
Posts: 644
Joined: Mon Oct 21, 2002 1:14 am
Location: Perth

Post by cbr »

wanna wrote:turbo 350 good how you going to bolt it behind your 253 adpter plate or redrill the block 700 good but bad points are weight length and cost to rebuild i can get a 350 that will handle 400hp for 1000$ a 700 will cost nearly 3 times that for the same hp


Yea it is expensive, but you get a lower first gear and an over drive!!

8runner, if you need an adapter for a 253 to a t350 bolt pattern I have one.


Chris
Posts: 2149
Joined: Sun Oct 20, 2002 6:59 pm
Location: gold coast, australia

Post by NICK »

i could be wrong but isnt a t700 about 7 inch longer than a 350, a 400 and 700 are the same length right?

so you would need a 350 with the rear removed and the adaptor to run dualcase with out cutting the horse collar?


am i smoking crack again?


NICK
TECH SCREW GURU
Posts: 2254
Joined: Tue Dec 10, 2002 5:09 pm
Location: Sydney

Post by jessie928 »

Without a DOUBT,go the TH700R4, Behind a 253, 308, 307, 327 they are all you need standard. If you putem behind a 350,400,454 you need to install the go fast bits for performance and longelivity.

It is strong ( although not as strong as a 400), and it has a 4th gear!!

as for length, i danno, but its a piss easy fit in a lux.

Jes
Posts: 48
Joined: Wed Nov 06, 2002 1:49 pm
Location: Melbourne

Post by pjhsv »

I'd go a TH400 if I were you. I had one in my Nissan G60 behind a reasonably 'warm' 308 (cam/exhaust/extractors/carb), and I used to be able to stick it in neutral, hit the loud pedal till the needle bapped 5g's, put it back into drive, no worries. Spoke to an auto trans place near me (the guy used to race Funny Cars), and he reckons TH400 is the only way to go if you're gonna be giving it a bit of stick. TH700 is good with the overdrive, but for the same size box, i'd rather extra strength personally.
Posts: 2254
Joined: Tue Dec 10, 2002 5:09 pm
Location: Sydney

Post by jessie928 »

someone i know V6 and V8 commodors in about 91, they had a stretch of wide quiet PRIVATE road they used to play on, Some of the antics were flying along at about 100clicks, putting the foot flat down on the load pedal and putting the car in reverse.

Good fun, no bangs or crunches... an interesting spectacle and Ride.
Post Reply

Who is online

Users browsing this forum: No registered users and 147 guests