Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
td42 rebuild or conversion?
td42 rebuild or conversion?
although i haven't had a comp test done yet, pretty sure i need a rebuild. but i'm wondering whether i should get it rebuilt, by a 2nd hand td42 or go complete conversion. what does everyone think? i'm not overly cashed up which is prob going to be a bit of an issue....
Re: td42 rebuild or conversion?
been done a few times
conversion : expensive.
Rebuild: if you get it done $7000 properly, head, cams etc (recently done by bloke in club, although he had 2 bent rods)
Used donk: they are around - probably the cheapest.
Ebay: $4000 for "rebuilt" engine.
conversion : expensive.
Rebuild: if you get it done $7000 properly, head, cams etc (recently done by bloke in club, although he had 2 bent rods)
Used donk: they are around - probably the cheapest.
Ebay: $4000 for "rebuilt" engine.
td42 rebuild
Why do you think you need a rebuild?.
Does it blow smoke , have no power ?.
Does it blow smoke , have no power ?.
joelt wrote:blowing smoke bad, white-ish blue smoke.....i also need the injector pump re-sealed. maybe, hopefully that is causing the smoke, but somehow i doubt it.....it's got enough power but it's also blowing blow-by smoke but only lightly.
How many K's on the motor? Could just need a re-ring kit to get another few years. Might be a cracked compression ring if ya getting blow-by vapor. Have you had head troubles/loss of coolant? If ya gonna open the head to re-ring may as well rebuild the head as well. Thats the prob you see... once you open her up its hard to know where to stop. Do a compression test to see if that shows up anything.
Good luck with it all and keep us informed.
Here is a test to find whether your mission on earth is finished: If you’re alive it isn’t.
- Richard Bach
- Richard Bach
Thats what i got, it doesn't include pump, injectors etc so thats extrabogged wrote:yea saw that, but cant be much of a rebuild for that price.trex wrote:Reco engines on ebay by East Coast 4wd $3300
Done about 7'000km's so far & very happy so i say go for it!!!
Style Side Maverick Ute
4.2 Turbo Diesel
35" Simex
4" Procomp suspension
2" Bodylift
Fibreglass Stuff....
Now highmount & Plasma :d
4.2 Turbo Diesel
35" Simex
4" Procomp suspension
2" Bodylift
Fibreglass Stuff....
Now highmount & Plasma :d
I remember Nicks parts came to more than 3k though...Big Red Toy wrote:Thats what i got, it doesn't include pump, injectors etc so thats extrabogged wrote:yea saw that, but cant be much of a rebuild for that price.trex wrote:Reco engines on ebay by East Coast 4wd $3300
Done about 7'000km's so far & very happy so i say go for it!!!
glad its stayed together for u....
http://cgi.ebay.com.au/Nissan-Patrol-Fu ... dZViewItemtrex wrote:Reco engines on ebay by East Coast 4wd $3300
Exchange yours for an unknown?!!!
Here is a test to find whether your mission on earth is finished: If you’re alive it isn’t.
- Richard Bach
- Richard Bach
Know how you feel. I'm going through the same thing at the moment. Mine took in dust one weekend (got past the airfilter), then a little bit of water the next. Getting a comp test done next week to find out how bad it is. Still seems to drive alright, but it's just not the same.joelt wrote:getting a compression test done next monday. see what they say and then i'll take it from there. injectors are fine, had them checked already, need a pump overhaul as well. man, it's so demoralising
How much would a second hand turbo intercooled TD42 from a GU go for? I'd imagine it would drop straight in.
Seen this one on eBay. $14 000!!!!!
http://cgi.ebay.com.au/NISSAN-TD42-PATR ... dZViewItem
turbodave wrote:Know how you feel. I'm going through the same thing at the moment. Mine took in dust one weekend (got past the airfilter), then a little bit of water the next. Getting a comp test done next week to find out how bad it is. Still seems to drive alright, but it's just not the same.joelt wrote:getting a compression test done next monday. see what they say and then i'll take it from there. injectors are fine, had them checked already, need a pump overhaul as well. man, it's so demoralising
How much would a second hand turbo intercooled TD42 from a GU go for? I'd imagine it would drop straight in.
Seen this one on eBay. $14 000!!!!!
http://cgi.ebay.com.au/NISSAN-TD42-PATR ... dZViewItem
i have picked a 2 gu complete engines now one was from here, i got it for $3800... the other was for $4200.. they can be had for cheap. failing that buy a rolled gu at auction.. cheap as...
cheers mark
Mud4b/ OPT, Cheap rates, Not cheap work. Search Opt- option offroad on facebook. Call or Sms 0439609525.. Sunshine coast, Eudlo, 4554.
[remember Nicks parts came to more than 3k though...
glad its stayed together for u....[/quote]
All up, my rebuild was just over 7K. Parts alone came to 5K using all Ni$$an bits. I did all the assembly work including replacing cylinder liners.
I had a shop do the cam bearings--very difficult to replace yourself, as you need a tool to ensure oil holes are lined up. Same shop ground crank and balanced--all up came to around $1800 i think.
Cylinder head overhaul came to 2K--this included replacing all the precomp chambers,valve seats,guides and seals and valves--i also had same shop replace gudgeon bushes and ream to size.
Nick
glad its stayed together for u....[/quote]
All up, my rebuild was just over 7K. Parts alone came to 5K using all Ni$$an bits. I did all the assembly work including replacing cylinder liners.
I had a shop do the cam bearings--very difficult to replace yourself, as you need a tool to ensure oil holes are lined up. Same shop ground crank and balanced--all up came to around $1800 i think.
Cylinder head overhaul came to 2K--this included replacing all the precomp chambers,valve seats,guides and seals and valves--i also had same shop replace gudgeon bushes and ream to size.
Nick
Who is online
Users browsing this forum: No registered users and 0 guests