Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

1.6L mpfi intake on 1.3L carb

Tech Talk for Suzuki owners.

Moderators: lay80n, sierrajim

Forum rules
Post Reply
Posts: 713
Joined: Tue Nov 05, 2002 2:12 pm
Location: Brisbane

1.6L mpfi intake on 1.3L carb

Post by Hybrid »

I know this is a big ask but is there any chance the 1.6L mpfi intake manifold will bolt to the old sierra 1.3 carb motor? I think I read something about it ages ago but I'm not too sure what the outcome was and I can't find the thread. I ask because I'm going giving a megasquirt a shot and I'd prefer mp over tb injection.
Top
Posts: 3722
Joined: Sat Jan 18, 2003 7:32 pm
Location: perth wa

Post by bazooked »

i did a 1.6 mpfi complete engine conversion in my old zook, your much better of doin the whole conversion imho for the bigger power gains, and the inlet manifold is totally different bolt pattern. the tbi from memory will bolt on.
buggy time............
Top
Posts: 713
Joined: Tue Nov 05, 2002 2:12 pm
Location: Brisbane

Post by Hybrid »

Cool. Thought that would be the case. I'd love to do the full 1.6 mpfi engine swap but i was looking for something cheep cheep as the budgie says.

Thanks mate.
Top
Posts: 713
Joined: Tue Nov 05, 2002 2:12 pm
Location: Brisbane

Post by Hybrid »

Will the G16 TBI throttlebody fit on the g13 carb intake or will i need to get the complete throttlebody/intake manifold?
Top
Posts: 3722
Joined: Sat Jan 18, 2003 7:32 pm
Location: perth wa

Post by bazooked »

Hybrid wrote:Will the G16 TBI throttlebody fit on the g13 carb intake or will i need to get the complete throttlebody/intake manifold?
if its single point injection you will need the inlet manifold etc, just make sure the manifolds are the same stud pattern.
buggy time............
Top
Posts: 7345
Joined: Wed Jun 02, 2004 3:29 pm
Location: Melbourne

Contact:
Contact Gwagensteve

Post by Gwagensteve »

(even if you could) by the time you had fitted the EFI vit manifold, injectors, loom, O2 sensor, fuel rail & reg, tuned it to work with the much more restrictive head and less capacity, etcetcetc, you woudl have been far better off going with the G16 to start with.

You could try swapping the whole head to the SOHC 16V 1.6 head, but to get everything you needed I think it would come with a 1.6 bottom end too.

The TBI swap might work, but I think you will need the intake manifold too.

Steve.
[quote="greg"] some say he is a man without happy dreams, or that he sees silver linings on clouds and wonders why they are not platinum... all we know, is he's called the stevie.[/quote]
Top
Posts: 176
Joined: Tue Dec 11, 2007 10:10 pm
Location: Perth

Post by scooby_74 »

You can buy an adapter for a swift 1.6 cpi to go straight onto the sj manifold. the hard bit is playing with electrics and mounting the fuel pump.
The mpi manifold onto the sj 8 valve head is just too hard and the 16 valve head requires 16v pistons all costly
Top
Posts: 65
Joined: Wed May 24, 2006 7:20 pm
Location: sydney

Post by terrazuki »

the boys at overkill hooked mine up to my 1.3 L and it wasnt to hard i think they do kits
go injection :) :)
ROCK RASH RACING #012





Uni filter
Top
Post Reply

Return to “Suzuki”

Who is online

Users browsing this forum: No registered users and 0 guests