Has anyone used these extractors?
Do they really exist?
How come I can’t find anything about them on the net, anywhere?
http://www.suzistore.com.au/shopdisplay ... at=EXHAUST
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Grand Vitara 2L Extractors (Installed with Pics)
Grand Vitara 2L Extractors (Installed with Pics)
Last edited by bendev on Fri Jan 16, 2009 1:34 am, edited 1 time in total.
Good Bye Grand Vitara, Hello 100 Series.
Fitted the Extractors the other day, Bolt in my eye.
Don't get me wrong there a great product but did they just forget to finish welding them?
So after i finished welding what was forgotten I had to run them on the linisher because when I tested how flat the flange plate was with a straight edge they failed.
After all this the rest was simple, until I had to bolt the flange up under the car. It was totally the wrong size.
Apart from these little defects, there great. Noticeable power gain, and just a little more noise.
Don't get me wrong there a great product but did they just forget to finish welding them?
So after i finished welding what was forgotten I had to run them on the linisher because when I tested how flat the flange plate was with a straight edge they failed.
After all this the rest was simple, until I had to bolt the flange up under the car. It was totally the wrong size.
Apart from these little defects, there great. Noticeable power gain, and just a little more noise.
Good Bye Grand Vitara, Hello 100 Series.
As in there ad.Ridge wrote:the best way to have that stuff fitted is to take it to an exhaust shop. would be $100 to fit it properly, align flanges and weld it all up.
when you spend $375 plus shipping and buy EXTRACTORS
(part# 14111-770EXN)
for GRAND VITARA SQ420
1998-2005 Motor J20A EFI 2.0L 4 Cyl
You would think they just fit up to a:
GRAND VITARA SQ420
1998-2005 Motor J20A EFI 2.0L 4 Cy
and not have to be modified.
Good Bye Grand Vitara, Hello 100 Series.
I wonder if they would fit my 97 wide track j20a vitara?
---------===== LOWRANGE JUNKIE =====---------
atari4x4 build up ~ MT/R 31's, calmini, body lift, j20a, 5.12 r&p + other stuff ~
http://www.outerlimits4x4.com/viewtopic ... 6&t=162392" onclick="window.open(this.href);return false;
atari4x4 build up ~ MT/R 31's, calmini, body lift, j20a, 5.12 r&p + other stuff ~
http://www.outerlimits4x4.com/viewtopic ... 6&t=162392" onclick="window.open(this.href);return false;
Well down low in the rev range it feels like it pulls a little bit more, but i'll really tell this week end when I go for a drive down stockton beach.TheOtherLeft wrote:
FWIW, did you notice any difference in performance?
Under a bit of load climbing some dunes I'll should know thenl.
I'll keep you posted.
Good Bye Grand Vitara, Hello 100 Series.
Liam wrote:They look like they were Pacemaker brand.
The flange may have been flat before the welding.
Nah, they were a bit bowed when I got them, don't get me wrong not a lot, but enough to worry about. The few people I spoke to said they will be Ok and that they would probably pull up but better be safe than sorry.
Good Bye Grand Vitara, Hello 100 Series.
Who is online
Users browsing this forum: No registered users and 27 guests