Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Converting diesel instrument cluster to petrol cluster

Tech Talk for Cruiser owners.

Moderators: toaddog, Elmo, DUDELUX

Post Reply
Posts: 25
Joined: Thu Dec 14, 2006 1:16 pm
Location: S.E Melbourne, VIC

Converting diesel instrument cluster to petrol cluster

Post by dar_sbb »

Hey guys,

i run a 1uzfe in a diesel surf. I have been running an aftermarket tacho but would like to use the standard cluster.

I went out and got a petrol 4runner cluster (off ebay) and plugged it up and all is fine... just the tacho isnt working. I have a direct tacho wire that i was using for the aftermarket gauge... what i was wondering was can i splice this wire into the standard cluster to make the gauge work? or is there something else that i need to do?

Image

This is a pic that i have of the dash... if this helps

thanks

daz
1990 Toyota Surf
LN130
1UZ-fe
4.0L
32 valve quadcam V8
Posts: 745
Joined: Sat Aug 02, 2008 9:45 am
Location: Vanuatu/ QLD

Post by thrashlux »

yes splice that wire to a wire going directly to the petrol tacho BUT make sure that there is none of your other wiring conected to the tacho run it as a stand alone if you do not the diesel loom will load up the output from the computer/igniter module and stop it from activating your tacho

dont you love how toyota uses 4cyl tacho for their v8
80 series 1980 hilux cab supra twin turbo engine
1hdfte 80 series
LHD fz 80 series GX
Posts: 25
Joined: Thu Dec 14, 2006 1:16 pm
Location: S.E Melbourne, VIC

Post by dar_sbb »

where do i splice it in the tacho? as it is part of the cluster... there are only the 4 plugs that plug in...?
1990 Toyota Surf
LN130
1UZ-fe
4.0L
32 valve quadcam V8
Resident Terrorist
Posts: 4278
Joined: Fri May 21, 2004 9:37 am
Location: Driving Barnsey's mum to bingo

Post by RAY185 »

That picture is fuzzy down the left hand side. What is the symbol next to tachometer. Bottom Left.
Posts: 745
Joined: Sat Aug 02, 2008 9:45 am
Location: Vanuatu/ QLD

Post by thrashlux »

dar_sbb wrote:where do i splice it in the tacho? as it is part of the cluster... there are only the 4 plugs that plug in...?
the safest way is directly to the screw on the back of the cluster to the tacho its self

there should be 3 screws one for IG one for GND and one for the pulse wire Used to go the the neg of the coil

use a ring terminal and put a piece of tape over the contact on the back of the cluster then insert the screw poking a hole in the tape.
Do this for the pulse wire only that way only the ring terminal and the screw are in contact isolating the rest of your diesel wiring in the car


jonathan
80 series 1980 hilux cab supra twin turbo engine
1hdfte 80 series
LHD fz 80 series GX
Posts: 25
Joined: Thu Dec 14, 2006 1:16 pm
Location: S.E Melbourne, VIC

Post by dar_sbb »

thanks guys for ur input. I will give it a shot and let u know whats happens

daz
1990 Toyota Surf
LN130
1UZ-fe
4.0L
32 valve quadcam V8
Posts: 25
Joined: Thu Dec 14, 2006 1:16 pm
Location: S.E Melbourne, VIC

Post by dar_sbb »

thanks jonathan... worked like a champ.
1990 Toyota Surf
LN130
1UZ-fe
4.0L
32 valve quadcam V8
Posts: 745
Joined: Sat Aug 02, 2008 9:45 am
Location: Vanuatu/ QLD

Post by thrashlux »

dar_sbb wrote:thanks jonathan... worked like a champ.
no wories

cheers

jonathan
80 series 1980 hilux cab supra twin turbo engine
1hdfte 80 series
LHD fz 80 series GX
Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests