Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Warn 8074 or 8274

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

Warn 8074 or 8274

Post by want33s »

Looking at replacing my lowmount winch with a Warn hi-mount.
Just want to know which is the better unit? The 8074 or the 8274?

Are both able to be upgraded, motor and drum.

I will be upgrading to at least a 6hp motor maybe a 7.6 if I can get one at the right price.
Top
User avatar
Guy
Posts: 10366
Joined: Thu Dec 12, 2002 8:43 am
Location: Wangaratta

Re: Warn 8074 or 8274

Post by Guy »

want33s wrote:Looking at replacing my lowmount winch with a Warn hi-mount.
Just want to know which is the better unit? The 8074 or the 8274?

Are both able to be upgraded, motor and drum.

I will be upgrading to at least a 6hp motor maybe a 7.6 if I can get one at the right price.
the 8074 is pretty old
" If governments are involved in the covering up the knowledge of aliens, Then they are doing a much better job of it than they do of everything else "
Top
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

Post by want33s »

I sort of figured the 8074 would be an older model but is it weaker?
Is it different?
Can I use all the upgrade bits available for 8274 on a 8074?
Top
Posts: 3
Joined: Mon May 12, 2008 10:46 pm
Location: Boronia

Post by BDOZER »

8024 does not have free spool, ie no pull leaver on top hat. Otherwise same strength. Just older.
Top
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

Post by want33s »

BDOZER wrote:8024 does not have free spool, ie no pull leaver on top hat. Otherwise same strength. Just older.
Cheers.. I want to fit an air free spool so that rules out the 8074 unless it can be retrofitted?
Top
Posts: 1041
Joined: Wed Jan 07, 2004 1:09 pm
Location: Melbourne, Victoria

Post by Mudzuki »

That depends if you are running an air free spool that is just an actuator on the 8274 lever, leaving the gearbox still running with the drum, or go for a drum disconnect.

I run the older style and find it great, both on my old zuk and now on my gu.
Top
Posts: 2877
Joined: Mon May 10, 2004 9:46 pm
Location: Goodna QLD

Post by ludacris »

Ring Dave Metcalfe to find out any info. You need to find out whether the little cog can be changed in the 8074 to fit the 6hp motor splines. Which one is cheaper and by how much.

Cris
Cris's 4 X 4 Accessories & Suspension 0404 736 325 Rock Sliders From $499
Top
Posts: 1041
Joined: Wed Jan 07, 2004 1:09 pm
Location: Melbourne, Victoria

Post by Mudzuki »

I now have a 6hp motor on mine, just had to buy the splined gear.

However, you need to measure the position of the gear, and pin the motor shaft to prevent the gear from falling off, as there is no retaining device from the factory.
Top
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

Post by want33s »

ludacris wrote:Ring Dave Metcalfe to find out any info. You need to find out whether the little cog can be changed in the 8074 to fit the 6hp motor splines. Which one is cheaper and by how much.

Cris
Got a contact number for Dave?

The 8074 is a few hundred cheaper than the 8274 but is starting to sound like the hassles may not be worth saving a few hundred.
Top
Posts: 3
Joined: Mon May 12, 2008 10:46 pm
Location: Boronia

Post by BDOZER »

If you are going to fit an air freespool ie drum disconnect - Mal Leslie, Flamin Fab type the 8074 will be fine with a 6hp motor with new splined motor pinion gear to replace key type of old 2.5hp motor. The 8274 pull type free spool only disconnects pinion gear at motor. The rest of gear train rotates with drum in free spool mode.
Top
Posts: 2877
Joined: Mon May 10, 2004 9:46 pm
Location: Goodna QLD

Post by ludacris »

want33s wrote:
ludacris wrote:Ring Dave Metcalfe to find out any info. You need to find out whether the little cog can be changed in the 8074 to fit the 6hp motor splines. Which one is cheaper and by how much.

Cris
Got a contact number for Dave?

The 8074 is a few hundred cheaper than the 8274 but is starting to sound like the hassles may not be worth saving a few hundred.
David Metcalfe 0418 745 830

Cris
Cris's 4 X 4 Accessories & Suspension 0404 736 325 Rock Sliders From $499
Top
Posts: 3940
Joined: Wed Dec 27, 2006 1:09 pm
Location: Sunshine Coast Qld

Post by want33s »

Thanks guys... I'll make a call and educate myself a bit....
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 113 guests